Search:

Parameters for OM-C spindle orientation 6531 and 6577 one is position and the other is a shift. I would try 6531 first. Don't forget to write down your original values if you have not yet backed up...

Did your company recently buy the machine used? If so you may have incoming power reversed. WITH THE POWER OFF, switch 2 of the phases around on the machines main disconnect. It is also possible that...

It sounds like you hit a hard limit when you moved the table before disconnecting. Did you physically check that the plunger for the limit switch has come back out or are you assuming it did because...

You don't need to change any parameters. If you disconnect the solenoid valve wire harness next to the solenoids(grey Honda connector) you can trigger them manually to get the arm back to home...

Could you please let me know what parameter you changed for the M-code for the parts counter?

Here are a couple pages that may help.

Just found out it is channel 17 and can be used for data input/output but not DNC function.

Some machines have a keep relay for monitoring M3/M4 basically to check if the spindle is running during a feed (G01). Do you have a list of keep relays?

Does anybody know what channel I need to be on to use the USB port on the new Fanuc 0i-MD? I can't find it in any of the manuals and I talked to 2 people at Fanuc FA America today and they couldn't...

I knew the 1GB 80x Transcend Compact Flash cards that I bought would work. I was able to get them to work on all our machines 0i-mate-MD, MC, 0i-MD, MC, 21i-MB, 18i-MB and 31i-MA. I ended up...

I'm not an expert yet, but I will be by the time I figure this out. I found out that for the Fanuc systems the cards needs the 5 volt single power supply and not the 3.3 volt. They also say to format...

Thanks for the responses but I know it should work. I have a 1GB Transcend Industrial card, a 2GB and 4GB Transcend 80x that all work. I've also had 1GB and 2GB Kingston cards that worked also.

I just bought some Transcend compact flash cards and I cannot get them to work in the LCD side mount slot. The new cards are Transcend Compact Flash 1GB 80x. I started out by formating the card FAT...

You can also use a 4GB card for DNC if you get the right one. The one I found was the Transcend 4GB 80x (lightblue). The 4GB Trancsend will also work in your dataserver. If you are willing to spend...

Have you checked the machine tool builders parameter settings for the timers?

Does anybody know if I can update my work offset using a G-code in my program? What I have is a boring mill with an 18i-MB control with a quill controlled as the fifth axis(W) parallel to the Z axis....

Looking at the back of the control the same way as your picture, check the fuse in the lower right hand corner.

Make sure you have your I/O channel set to 5 turn the mode selector to DNC. Go to your HD-DIR and select the correct program press dnc-st and exec.

There should be keep relays that track the progress of the the A.T.C. and A.P.C. From my experience when the tool change or pallety change has completed bit zero of the specified keep relay reverts...

Since the alarm is not constantly on then there is probably a bad connection. I would start by checking the connections on the Fanuc drives. Shut the machine off, open the electrical and make sure...

I would put a magnet base with indicator on the table and check the runout of the cutter also.

There should be a keep relay supplied by the MTB that would control weather or not the axis rotates the shortest distance or not.

Check your lead in and lead out for the smaller holes and make sure the lead in radius is smaller than the finished holes radius.

You need to be on channel 5 for the ethernet hook up and set the IP address in the control to match the computer of network that you are connected to. You can use channel 4 for the card reader at the...

I found that the cards made by Kingston on work if they are 2GB or less. The original Sandisk will work up to 4GB but I found Transcend Industrial to be one of the best cards to get.

Does this happen right after a tool change?

Make sure your phase is correct. If there is a hydraulic unit or chiller the machine may not come ready if the phase is backwards.

Is this the one you are looking for?

Does this happen when you enable high speed function? There are parameters to change so different things can flash there. I once saw a machine that would flash ' *uckyou ' instead of ' ai nano '.

Does the noise go away or hear different pitches if you change the feed rate with the feedrate overide switch?