Search:

Yup! Forgot about the magazine on that one.

I believe it is your pallet changer (APC) that is considered the Aux axis. You need to rezero that to get rid of the alarm. It is under the AUX-MON page.

Parameter 1851,Z axis grid shift. As noted by other poster, write down original value and adjust accordingly. Fanuc uses metric numbers, and there is no decimal point used. So if you see 1000 in that...

M73- Parts Catcher out
M74- Parts Catcher in

Turret needs to be in correct position, somewhere closed to the spindle, if the parts catcher is on top.

I know this sounds a little stupid, but have you checked incoming power and if it is phased correctly? The hydraulic pump will not work if phase is backwards.

You will have to probably replace the PSU. I've come across where even after replacing the batteries, the BAT alarm stays on. I have had to replace the PSU to get rid of the alarm. The number is on...

Press the "Setting" hard key
Select "Communications" setting. I think its 64.
Use arrow key to highlight what I/O device you want to use.
Press the "Set" soft key.

The CAPS side does have a...

If you look at the grey Honda connector that is connected to the drive, it should have an X on it for X axis. It plugs in vertically from the bottom up.

If its the old type of CRT, and not LCD, you can open the operator panel and there are pots to control V-Hold, H-Hold and brightness. Maybe they need adjustment. If not, on the settings page, there...

Hey pal, you asked for an answer and we gave you one. No need to call people names.
I'm sure that just any ol' CNC will work for you if you don't want a Mori.

Good luck.

The purpose of the password is that Mori's machines cannot be located in unauthorized countries, like Iran and Iraq (http://www.nti.org/e_research/e3_90.html).
Mori's machines are too acurate and...

It requires new software, a new MAPPS display unit and maybe some Fanuc software. I've done a MAPPS upgrade from GOP3 to MAPPS 2. Took ABOUT 3 DAYS TO GET ALL THE CORRECT SOFTWARE AND PARAMETER...

There is a limit switch that reads when the arm is up. It is located in the slot where the latching mechanism goes into. It may be stuck and still thinks the arm is up. Spray some WD on it to loosen...

SWITCHING X AXIS DIRECTION ON LATHES WITH FANUC 6T CONTROL

1. Swap soft O.T. wires L1 & L2 on the terminal block in the magnetics cabinet.

2. On the JOG lever switch on the operators panel,...

Here is a link to a guy I know who used to work for Fanuc.
It is the parameters that are needed for communication.
He is a great guy that does drive rebuilds.

http://www.kfasllc.com/rs232_6.htm

It appears as though the magazine has not rotated 1 complete turn. Here is a PDF of the alarm.

220V A/C +/- 10%
198V-242V

You need to check your motor ratings to see what KVa's are needed.
There was once the power rating that the machine required stamped on the label that has the machine...

Does this machine also have a pallet changer?

I think you can change PMM parameter 40 to speed up the magazine. This will allow the one count to be read.
I've done the procedure 4 or 5 times on a MV-653 and it seems as though I always end up...

Here is a procedure on an SV-40. Should be pretty close.

Try this.
It's for an MX-2.
Should be close.

The newer MAPPS IV controls do have eSpirit on them. The older ones had CAPPS programming available that waould allow you to program on the machine and then you could output the program in G code....

If it is a small, yellow box-looking drive, it's a beta drive. A "0" usually means that the magazine needs a zero return performed. You can access the alarm menu of that beta drive thru the PMM menu....

We have a customer that has an NZ2000T3Y3 that runs 24/7 except for Sunday. They run really tight tolerances (+/-.0003). The lower turret (T2) has a 32 tool capability. It runs on both main and sub...

Try these.
They are labeled for a SV-500 and MV-653 18 control.

Shoot me an e-mail. I'll see what I can get.
[email protected]

jcg9393,

What type of control is on that ZL?
I may have something, but it's for an MSC-501/MSG-501 control.
Shoot me an email at [email protected]

Not that I know of.
Easiest thing to do is leave the Panel Edit key in the "On" position then remove the key. You cannot edit program without the Panel Edit key in the Edit position.

this is what I found.
hope they help.

Yes, Mori Seiki took over the line a few years ago. To get parts, you need to go thru the Mori distributor, Ellison Technologies.
Their parts hub would be able to identify any parts you may need....