521,637 active members*
2,374 visitors online*
Register for free
Login

Search:

Type: Posts; User: LouF

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2,361
    Views
    29,440

    Re: Super-PID new low-cost router speed controller

    I agree customer service is paramount.
  2. Replies
    2,361
    Views
    29,440

    Re: Super-PID new low-cost router speed controller

    Congrats that's great let us know when you recive your shipment.
  3. Replies
    2,361
    Views
    29,440

    Re: Super-PID new low-cost router speed controller

    Good Luck
  4. Sticky: Re: Router Bits and EndMills: Pictures, Descriptions, and Uses

    Hi what CAD and CAM software are you using and what machine are you using?
  5. Replies
    79
    Views
    12,199

    Re: Our wooden products

    Some very nice work they look great.
  6. Replies
    4
    Views
    50

    Re: I need cable chains.

    Here is where I purchased e chain for my machine you can get the same product cheaper on E Bay or Amazon https://www.igus.com/energychains
    Just google E chain.
  7. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Gerry, Okay after doing the setup without the G code loaded and it homed saying in the window on the run screen "Material Offset now Calculated in Inches" I loaded the g code I clicked run it moved...
  8. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Gerry, so is there a workaround this what should I do? I am lost on a solution to this everything worked well before I had my Hardrive cloned.
  9. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    The tool change position is set at.
    Fixed plate X: + 16.963
    Fixed plate Y: + 0.341

    After zeroing without g code loaded it goes through the routine like normal it stops above material like it...
  10. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    I do it with g code loaded I will try it without it loaded.
  11. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Okay, I set up my job center of the table I then click the auto-zero tool change Icon, my spindle moves down to the touch plate on the material. My spindle then moves to the second fixed plate...
  12. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    It sends me home after I do the setup touch both plates the box pops up to start spindle. So I manually start the spindle through SupPid click the box and it sends me home instead of cutting the work...
  13. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Gerry, thanks.
  14. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Part of the G code file.

    Thanks
    Lou
  15. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Gerry, can I email the file to you @ the email from your website?

    Lou
  16. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Gerry, I tried to upload the G code and I get this " Your file of 1.28 MB bytes exceeds the forum's limit of 500.0 KB for this filetype." not sure what to do.

    Lou
  17. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Well, I tried my machine with the change made now after setup it goes through the routine lose and fixed touch plates I get the start spindle pop up. Now after clicking the message box to start it...
  18. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Gerry, It was not checked that must be it.

    Thank You Gerry
  19. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Gerry, I am not sure I will have to go check and see.
    Thanks, Lou
  20. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Rodger, they are in the folder I noticed two different Mach 3 folders on my "C" drive they both have M6 End and M6Start marcos One is labeled Mach3 and the other labeled "Mach3 new" It has been so...
  21. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    I will check that out thanks..
  22. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    I am having a problem with Mach 3 and 2010 screen set I have been using it for years trouble free. I recently had my hard drive re cloned if that could have anything to do with it otherwise...
  23. Sticky: Re: Router Bits and EndMills: Pictures, Descriptions, and Uses

    I would lubrication.
  24. Replies
    3,150
    Views
    4,465

    Re: CarveOne's Steel Channel Rebuild

    I am also looking at the offerings from China.
  25. Replies
    3,150
    Views
    4,465

    Re: CarveOne's Steel Channel Rebuild

    CNC Router Parts I am looking at around 9K.
  26. Replies
    3,150
    Views
    4,465

    Re: CarveOne's Steel Channel Rebuild

    Happy to see you back I need a bigger CNC 4X8or larger any Ideas build one or purchase one?.
  27. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Thank you Gerry my old desktop running XP is making weird sounds so I may have to go to a laptop running windows 7..
  28. Replies
    1,466
    Views
    111,920

    Re: Mach3 2010 Screen set

    Gerry quick question will the 2010 screen set work with a touch screen?
  29. Thread: 2010 screenset

    by LouF
    Replies
    84
    Views
    8,331

    Re: 2010 screenset

    Gerry no entries in the tool table.
  30. Thread: 2010 screenset

    by LouF
    Replies
    84
    Views
    8,331

    Re: 2010 screenset

    Gerry can you give or PM me your Email so I can send you the files?
Results 1 to 30 of 500
Page 1 of 17 1 2 3 4