584,812 active members*
5,193 visitors online*
Register for free
Login

Search:

Type: Posts; User: RuslanRobot

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,347

    Using two KStep board

    Good day!

    We are going to use two KStep board in one mashine (using one KFLOP).

    1. How to conect KFLOP with second KStep board? (what JP we need to use?)
    2. What additional connecting wire we...
  2. Re: Manual control arrows - how to make inactive?

    I find!
    https://www.youtube.com/watch?v=uQWDttzKuDA&ab_channel=Dynomotion
    Thanks!
  3. Manual control arrows - how to make inactive?

    Please help me.
    How do I make the manual control arrows on the KMotionCNC panel inactive (turn off)? See the photo - circled in red. So that I can then turn it on if necessary.
    I need it in order...
  4. Re: Yellow axis after flashing (user memory) Kflop.

    YES! Work. Thank you!
  5. Yellow axis after flashing (user memory) Kflop.

    Good day!

    Help please.

    Here is the InitKstep4axis file (compiled without errors). I configured the INIT button on the KMotionCNC panel that runs file InitKstep4axis.
    Before flashing, when...
  6. Replies
    1
    Views
    534

    kStep board warms up to 75 degrees

    Good day!

    kStep board - warms up to 75 degrees Celsius, Kflop is heated to 52 degrees Celsius. See video: https://drive.google.com/file/d/17rL9gEgJiFfz4vynVt2tg7EyFqF6V6d3/view
    Warms 75 degrees...
  7. Re: Do I need to buy Konnect Optical I/O Expansion Board?

    Good day!
    kStep board-warms up to 75 degrees Celsius, Kflop is heated to 52 degrees Celsius. See video: https://drive.google.com/file/d/17rL9gEgJiFfz4vynVt2tg7EyFqF6V6d3/view?usp=sharing
    We use...
  8. Replies
    1
    Views
    438

    Microstep settings in Kstep?

    On a conventional stepper motor driver, the micro-step mode is set by dip switches according to the table.
    1. Where are microstep settings in Kstep?
    2. How to do auto-tuning microsteps in Kstep?
  9. Re: Do I need to buy Konnect Optical I/O Expansion Board?

    Let me reformulate my question (as am not sure, that I understand your answer):
    Opto isolated relay consume 9 milliamperes, 3.3V. Can we connect this relay to JP4 or JP6? Will this load spoil...
  10. Re: Do I need to buy Konnect Optical I/O Expansion Board?

    We are going to use opto isolated relay, and connect it to JP4 or JP6 - can you advise what better? (JP7 used with KStep).
    Where is described the milliampere current on JP4 and JP6? - we can't find...
  11. Re: Do I need to buy Konnect Optical I/O Expansion Board?

    I see the KStep Amplifier for KFLOP https://www.dynomotion.com/KStep.html

    It will drive 4 motors and emit heat.
    I don't understand - How to cool this board?
    Shold I buy radiator? - but I don't...
  12. Do I need to buy Konnect Optical I/O Expansion Board?

    Good day!

    I have 4 step motors, 1 stop buton, 8 end sensors, 4 pneumo relay for suction cups.

    I am going to buy 1) KFLOP, 2) KStep Microstepper Amplifier for KFLOP.

    Do I need to buy...
  13. Replies
    10
    Views
    1,519

    Re: Deviation in axis A and Z

    Here is the specification on my driver (it is on russian, please translate it by google)
    https://darxton.ru/files/pdf/stepperdrive/EM402.pdf

    Please tell me, - will it work with Kflop?
  14. Replies
    10
    Views
    1,519

    Re: Deviation in axis A and Z

    1. I bought another driver - Leadshine EM 402 (it supported CW/CCW mode). On the scheme, driver require VCC and ENABLE. What pins I have to connect on the Kflop to be connected to VCC and ENABLE? ...
  15. Replies
    10
    Views
    1,519

    Re: Deviation in axis A and Z

    This connection scheme was the plan, but in fact we wrong connected. So we need to do in accordance with this scheme.
    No, my drives don't need to be enabled.

    Thank you!
  16. Replies
    10
    Views
    1,519

    Re: Deviation in axis A and Z

    Can you tell me please , - is this connection scheme right?

    It seems to me, that in fact we connected something wrong.
  17. Replies
    10
    Views
    1,519

    Re: Deviation in axis A and Z

    I did these:
    1. To use Open Collector - Step/Dir mode, changed in the Init file: ch2->OutputChan0=2; ch3->OutputChan0=3; for axis Z and A respectively. The motors DON’T move, but the KMotion shows...
  18. Replies
    10
    Views
    1,519

    Deviation in axis A and Z

    Good day!
    I use this driver to control suction cups, axis A and Z, using micro step 16.
    After performing the Zero Axis, all suction cups are aligned. After starting the loop 100 times (G code Axis...
  19. Re: Can’t turn on axis (after turn off machine during G-code)

    Yes!!!!
    I am idiot. I tried to make Kflop work while ESTOP is on.....
    Everything is work.
    Thank you very much!
  20. Can’t turn on axis (after turn off machine during G-code)

    1. I pressed the button Home, - to home all axis (see file HOME_Axis.c). Machine start to go home, and during this I turned off the power.
    2. After 15 sec. I turn on the power. But in the screen of...
  21. Re: Invert signal from end sensor. Appointment signal as the emergency stop button.

    EStop button.
    EStopDisablesAll.c - Yes, i found this file, changed number of bit (inputs 10, bit 1034).
    On the menu M0-M30 in front of the Stop, choose Executing Prog, set number of program (Thread...
  22. Invert signal from end sensor. Appointment signal as the emergency stop button.

    Please, help me.
    I have two questions with sensors:

    1. I can't find where in the system KFLOP I can invert the input signal from end sensors. I have several end sensors of the Normally Open...
  23. Replies
    3
    Views
    946

    Re: How to make alive my pneumo-relay

    Yes!!!
    I did in accordance with your screen shot, and I can turn on/of lights on the board by G-code (M100 - lights on, M101 - lights off).

    But I connected relay to the Konnect without flyback...
  24. Replies
    3
    Views
    946

    How to make alive my pneumo-relay

    Please help!
    I dont understand - how to make alive my pneumo-relay.
    I have KFLOP + Konnect Optical I/O Expansion Board.

    Pneumo-relay connected to Konnect pins Out 12, 13, 14, 15.
    In the...
  25. Replies
    2
    Views
    798

    Re: Can't connecting Konnect to a Kflop.

    Yes it 's work!!! Thank you.
  26. Replies
    2
    Views
    798

    Can't connecting Konnect to a Kflop.

    Please, we need help!!!

    What was done (see attached files):
    Konnect was connected to the Kflop through jp6 whith a ribbon cable that was lying in the kit;
    in a C-file a Konnect board was...
Results 1 to 26 of 26