The probe is just a switch.
Maybe this info is useful: https://cnc4pc.com/blog/post/wiring-mechanical-limit-switches-on-a-c76
Arturo Duncan
https://cnc4pc.com
Type: Posts; User: arturod
The probe is just a switch.
Maybe this info is useful: https://cnc4pc.com/blog/post/wiring-mechanical-limit-switches-on-a-c76
Arturo Duncan
https://cnc4pc.com
You could get this working with these servos:
https://cnc4pc.com/dg4s-16035-dc-servo-drive.html
But considering the cost of AC servos or closed loop steppers and the high maintenance cost of the...
Nice looking? What control software are you using?
The higher the resolution the smoother the motion is, but you tend to lose torque. So you need to play with them while the motors are working under load until you get the optimal performance. Maybe...
Maybe these recomendations may help:
https://cnc4pc.com/faq/article/how-to-tune-stepper-motors
This unit cannot process the input signals in real-time, so input signals may not be that useful anyway.
If you are on a tight budget, you can retrofit this keeping the original motors and just replace the servo drivers:
https://cnc4pc.com/dg4s-16035-dc-servo-drive.html
If you do not intend to run...
Ethernet may be a much better option. Consider the UC400ETH. It is more stable.
Arturo Duncan
httpss:/cnc4pc.com
I think you are a good candidate for the C25XP from CNC4PC: https://cnc4pc.com/c25xp-smooth-stepper-integrated-board.html
There are tons of options for integrating it into a Plasma or Oxy/Cutting...
You need to configure UCCNC to control the spindle using PWM and use two outputs to control the FOR and REV signals. The info you are looking for is in the manual of the G540.
Arturo Duncan...
From what you are saying, I see that you have the jumpers set to operate the spindle on international mode. Check the jumpers and move them to US Mode. Note that on international mode relay1 is...
Here is how this works:
1. Your VFD is expecting FOR and REV signals, so make sure the jumpers on the C76 are set to US Mode.
2. Verify that when you call M3 Relay1 activates and when you call M4...
Maybe these instructions may help: https://cnc4pc.com/blog/post/uccnc-configuration-for-laser-module-on-c76
We have a connector board for those servos:
https://cnc4pc.com/c34svdb100-invt-sv-db100.html
Use Mach4 or UCCNC.
Arturo Duncan
https://cnc4pc.com
Replace this with a PC based controller.
Open a ticket and send pics of the electrical components and we will send you recommendations:
https://www.cnc4pc.com/contact
Please check these macros:
https://www.cnc4pc.com/forum/projects/tool-change-macro-for-uccnc
Arturo Duncan
https://cnc4pc.com
Check this out:
https://www.cnc4pc.com/blog/post/wiring-sample-for-atomstack-m30-laser-with-c76-board
https://www.cnc4pc.com/blog/post/uccnc-configuration-for-laser-module-on-c76
Arturo Duncan...
Did you get this sorted out?
Arturo Duncan
https://cnc4pc.com
The first thing that comes to mind, is to run the Utilityxxx software to reestablish the connection. Maybe you just need to whitelist the device on the networks firewall.
Please check this FAQ...
I am sorry for the delay in shipping your order. Today we made a partial shipment. The pendant remains backordered, but should be in early next week.
It all depends on the application. For simpler setups, you can use the C25XP which uses terminals:
https://www.cnc4pc.com/c25xp-smooth-stepper-integrated-board.html
For wiring more complex drives,...
For use with the C34 boards, we strongly recommend you use the C82:
https://www.cnc4pc.com/c82-dual-port-multifunction-board-b.html
You can open a ticket in our website and we may be able to help...
Check this:
https://www.cnc4pc.com/blog/post/C94-Connecting-with-CNC4P-Probes
Arturo Duncan
https://cnc4pc.com
Why has the C35 not worked for you? It is a very simple board. It is intended for single port systems using Closed Loop steppers or servos as it can connect to the fault/enable signals. Make sure...
UCCNC Runs in DEMO Mode when it cannot talk to the Motion Controller.
Arturo Duncan
https://cnc4pc.com
This is a noise issue. Here are some thoughts:
- Check that the negative of the e-stop is not common with the ground of the VFD.
- You may want to install a filter on that VFD.
Arturo Duncan...
The deadline for applying for the C25XP giveaway will be June 2nd. This allows time to evaluate and select the winner.
Arturo Duncan
https://cnc4pc.com
Checkout the C94 for this machine:
https://www.cnc4pc.com/c94-multifuntion-board-b.html
Arturo Duncan
https://cnc4pc.com
The installer will configure everything, so do not worry about the pinout stuff, that is there in the manual just for your reference.
What you are describing, is that the board is seeing a servo...
The C41S and C11G use the same circuits and the configuration would be the same if using the same software and pins. Michael82, you should be able to get the system to work by carefully following...