So my Daewoo Puma 6 just decided to throw this code, svo13, and the machine will not reset and come on. The code is z improver v ready off. I have read a couple other post about this code and I have...
Type: Posts; User: tfuqua63
So my Daewoo Puma 6 just decided to throw this code, svo13, and the machine will not reset and come on. The code is z improver v ready off. I have read a couple other post about this code and I have...
I am receiving alarm code 4 on the spindle drive
Just recently purchased a daewoo puma 6 with fanuc 10 controls. Just plugged the machine in and started it up. I ran the spindle in low gear for a few minutes (not fast just slow rpm) then I stopped...
Got my machine running :banana:had a local tech come out lucky for me he new my brother inlaw and gave me a really good deal on helping me get it up and running. I was close but would probably never...
I am interested in knowing how your project is coming along. I have bought an older Mori SL1 and will be looking into doing something similar
Check this out it is pricey but it should work Centroid All in 1 DC servo CNC Control Kit
I am retrofitting an old Hurco and I am using the DSPMC from Vital systems they have what you need as well...
I have an alarm 17 on my Kit MC1 and have a tech coming out tomorrow to help get it running I will let you know if we get it going how we correct the Spindle Alarm.
It was my understanding that...
Here's some pics of my current screen
328318328320328322328324
I was able to enter the 300 and 400 DGN Parameters this evening but still have not been able to do anything yet other than actuate the tool release and lock ? I did notice that my screen was missing...
Ok found out I have more parameters to enter ; some 300's and a few 400's, Found them on a data sheet that came with my machine. I will get them put in and see what happens ?
I will be crossing my...
I need 3 tool pots for my machine BT 35 tool holders Kitamura MC 1 let me know where I might could find these at ?
Yep Thanks I finally figured that out it was 0's and 1's or other numerals in other locations. I was able to get the parameters loaded back into the machine got it starting up with no errors on the...
Good luck hope you can find something before you have to spend the big bucks.
Made some progress today got the parameters back in machine starts up with no alarms but I can not move any axis and I know the axis are not where they are supposed to be here are some pics of my...
Pic of my key board
327716
What control does it have ? I am sure you could find parts for that on epay ?
Kitamura MC 1 ser.#02196
I have lost parameters on this machine and have researched how to put them back in but when I get to the point of actually installing them I have ran into a snag and need...
I used purple power engine degreaser (don't get it on stickers or signs it will remove lettering) and a condenser comb you can find them at A/C suppliers :) that and a spray bottle with water for...
327128327130327132327134
Here are some pics of what I have
I have tried to clear the machine by pressing Delete and Reset at the same time while powering up but nothing changed ?
I have a Kitamura MC 1 with a Fanuc OM-B control I have a 911 alarm RAM PARITY (HIGH)
From what I have come up with the batteries have died and I need to delete the system and re enter the...
Thanks I have done that it did clear the Alarm code but still no Axis movement ? Thanks
Got my machine inside cleaned up hooked up power and air. Powered it up screen comes on and I had an Alarm 531 -Z axis limit switch so I cleared that up (switch was stuck) and tried it again. I can...
Need HELP have powered up my machine and have Alarm code 531 have tried the instructions in the manual and have not been able to get it fixed. Its says to enter G23 How can I enter G23 to fix the...
Went to the auction to buy one machine but came home with two consecutive serial numbers. - - - 95, - - - 96 the 96 looks to be in better shape has new screws as well. plan to get them both up and...
Finally got the twins home not in the shop yet one is still on the trailer and the other is on the ground. I've built a skid for them bolt it to the base and I can skid it into the shop to get them...
Man I am glad you found my post you are probably the only one left besides me who has those drives ? i will get in contact with you on that I have figured some of it out but a schematic of the drive...
Looks like a couple may be carbide ? Put them on epay 5 in a lot plus shipping and you will know exactly what thay are worth.
I can see how the gear works but :confused: Are the copper pieces actually making contact how is that working ?
Why did you have to add the encoder on the spindle did it not have any thing on it already ?
I would like to see a list of the hardware you purchased to make this happen if possible and some more...
I have the manuals for both controls pm if still in need