Search:

[email protected]

Hi every body.
we have a problem with our puma 240L turret.
when turret turn and get on desired angle it turn backward ( about 1-5 deg , this amount is different for each station ). operators have...

I appreciate all responses.
the q-setter interface board is under repair.
but now we have another problem with the turret.
After tool change the turret turn about 5deg backward. and the backward...

Hi.
first I have to correct my previus post.
only the X+ change on PMC status. but none of the others.
on the interface board there are 4 LED that any one of them shows a signal received from the...

OK i will check that. but when the tool touch the probe, the red lamp on center of probe turn on. doe's this lamp turn on if the wire is broken?

when the tool tip touch the probe, none of x4.2 - x4.5 changes. all of them remain zero.
but some other parameter, that i checked, in the status of pmc parameter change as they should.
so is the...

thanks for your kindly guidance.
i could find it.
now i think i must touch the probe in X+ , X- , Z+ and Z- . and check the changes in X4 line.
is it right?

Hi.
i checked out the ladder and electrical manual. mine either. X4.2 for +MT1.M , x4.3 for -MT1.M , X4.4 for +MT2.M , and X4.5 for -MT2.M.
but now i don't know how to check it on the machine. how...

1. yes it doe's. the display change to offset page with the cursor on the active tool. (parameter 5005.#5 is 1)
2. yes. keep relay K7.5 is 1 ,it means Q-setter is attached to the machine. and also...

X and Z work in all modes.
but the problem is with Q-Setter.
none of them wont stop when touch the probe.
older operators in our company told me : it had worked before, but the X tool-offset was...

Hi.
thanks for your attention.
yes, it has worked before, but with error in X direction ( i think it just needed calibration) but they tried to repair it ... and now this is it's situation !!! ( i...

Hi every body.
We have a problem with our PUMA 240L machine's quick tool presetter as flow:
we do all according to its user manual. when tool touches the probe, the red lamp in probe center will be...

Hi.
for 4 & 5 axis post processor of powermill you can contact with me directly [email protected]

Hi every body.
If you need a 5 axis post processor for powermill for any controller and any machine kinematic ; Please feel free to contact me : [email protected]
I will do it for 300 to 500 USD....

Hi every body.
If you need a 5 axis post processor for mach3 or other controllers ; Please feel free to contact me : [email protected]
I will do it for 300 to 500 USD. i will get the money after...

[email protected]

Hi.
yes certainly it is possible to generate a g-code without error for any controller either mach3.
I can write post processor for any type of 3 axis and 4 or 5 axis for mach3 , so that the g-code...

Do you need a 3 axis post-processor or 4 axis or 5 axis?

Hi.
you could create a new work plane and rotate it around your machine rotary axis. and do your 3axis machining in new direction. you should rotate the rotary axis manually. It called 3-2...

Do you need a 4 axis or 5 axis post-processor?

Hi
in fact you need a 4 axis post processor for your machine.
Which type of Roland do you have?
I can write for any 4 axis or 5 axis machine its own post processor.
for more detail contact :...

Hi.
For 3 axis machining you can use fanuc6m. But you should edit the begin of G-code. but for 4 axis or 5 axis you should have the Multi Axis Post-processor.
Also you could have a 3 axis...

Hello.
I'm in dealling with multiaxis CAM solutions. I can write Powermill PostProcessor based on Duct post or PM post, special for your machine according to its specification and kinematics.I can...

for 5axis postprocessor send me your machine specification
[email protected]

Hello.
I'm in dealling with multiaxis CAM solutions. I can write Powermill PostProcessor based on Duct post or PM post, special for your machine according to its specification and kinematics. I'm...