584,842 active members*
4,398 visitors online*
Register for free
Login

Search:

Type: Posts; User: dghele

Search: Search took 0.00 seconds.

  1. As gizmo_454 mention only few can handle the full...

    As gizmo_454 mention only few can handle the full features of swiss. I use solidworks+solidcam usually but for swiss I was forced to go with something else. I choose Esprit where I found the post and...
  2. Help with Bios settings for Cincom/C32 Meldas600

    Hello , need help with BIOS config for c32 VII(2004) due to battery failure (without any formal warning).
    Initially with the default BIOS settings could not boot due to keyboard missing. I manage to...
  3. Replies
    6
    Views
    6,204

    Thanks Is different for M32. Anyhow I found one...

    Thanks
    Is different for M32. Anyhow I found one but it is not exporting coordinates; only Gcode
    Need more time to figure it out.
  4. Replies
    3
    Views
    3,052

    Re: Esprit post for Citizen C-32

    I'm looking as well. Is a Meldas 600 control. The E-32 is not working for me.
    Anyone have some post close to so we can modify ?
  5. Replies
    4
    Views
    2,030

    Re: Need help to zero A1, A2, A3 Citizen C32

    I thought no one will answer.Thanks a lot for advice.My plan was to disconnect the lines from the pump and inject & air blow some engine oil (which contain stronger detergents) to melt all this...
  6. Replies
    4
    Views
    2,030

    Re: Need help to zero A1, A2, A3 Citizen C32

    Zeroing procedure sorted; I finally found the page.

    Q For Cincom users: My machine was out of production for more than a year and almost all my axes are dry at the moment;I can apply oil on rails...
  7. Replies
    55
    Views
    14,223

    Re: Fanuc 10M - Drip Feed

    As an update: I manage to get Tape Mode on my 10M machine. Cassette ladder was modified by adding G12.3 and SW updated to 1021 SW to allow it to work.
    Maybe will help someone someday :)
  8. Replies
    4
    Views
    2,030

    Need help to zero A1, A2, A3 Citizen C32

    Just bought a Citizen C32 with Meldas600 and Intelligent motors. I finally manage to get the axis zeroed using procedure and manual jog pressing against end but I can not zero A1, A2, A3( for front...
  9. Replies
    6
    Views
    6,204

    Post processor for Citizen Cincom C-32

    Hi Guys,

    Can anyone help me with a post processor for Citizen Cincom C-32?? I just got the machine and I think Esprit is the easy way forward.Just want to give it a try.
    I would prefer SolidCam...
  10. Replies
    55
    Views
    14,223

    Re: Fanuc 10M - Drip Feed

    CNC2149 wrote:

    " I did a job in 1996 on a 10MA Analog (1020 SW) where I added the DNCI PMC bit (G12.3) to their 3MI compatible ladder and when we attempted to run drip feed, it would result in...
  11. Replies
    55
    Views
    14,223

    Re: Fanuc 10M - Drip Feed

    Hi

    My machine have a serial port and I can load and save programs but I can not enable drip feed function. I do not have TAPE mode and the machine is using FS3 interface. As far as I red till now...
  12. Replies
    55
    Views
    14,223

    Re: Fanuc 10M - Drip Feed

    Any Help guys?? No one? At least somthing to start with.

    Thanks
  13. Replies
    55
    Views
    14,223

    Re: Fanuc 10M - Drip Feed

    Hi guys,
    I know is an old post but is related with drip feed so... I will ned your help and guidnes. I've read very carefully the previous posts and I will describe below all the information about...
  14. Replies
    8,430
    Views
    318,938

    Sticky: Re: Welcome thread-tell us about you.

    Hi guys,

    I'm Daniel and I found out and register to this forum because I need some guidness and help. I start building my own design CNC(router) back in 2003. Since then I added to my colection a...
Results 1 to 14 of 14