ho folks anyone that can help with the tool changer recovery? 2007 DMU50
Type: Posts; User: Magpie26869
ho folks anyone that can help with the tool changer recovery? 2007 DMU50
Hi folks. Looking for any manuals for a 1998 mv50 Mori seiki.
Hi folks. Getting an intermittent alarm. Mori suggested the switch. Changed it will no success. Tech has been out twice. Machine won’t work when they get there and comes
back to life when they start...
Hi folks. i have a mori frontier l1. it has a bar feeder that is not being used. i know what needs to be done but the problem is i cant find the emg3 and 5 wires in the cabinet to jump them off....
im not familiar with this control on the lathe. i ran a frontier mill that had one. never used the graphics. dont know if it had any. i have employees and they like the graphics. are there any on the...
Hi folks. i am thinking of buying a a 99 mori frontier lathe. it has an msc521 control. does any one know if this control has graphics? is this the same control as the fanuc 21? thanx
thank you for the reply. i will look at this manual and compare to what i have. i might have narrowed it down to the interface which i change because the CTS, was down and the auger was not function...
morning folks. can anyone give me any information on the pressure switche used with the coolant through system? i believe the pressure is set too high and drawing too much coolant when the return...
thanx for the reply. i got the key to the door. no luck. still leading to the interface. think im going to just order it. im waiting for help with checking that grounding the ypin. now that you...
hi folks. any help with this one? machine is a vm20 with centurion7. buttons on panel that work are the flood air mist single block option stop. light will come on and function will work when button...
It is v26 I have at work. I knew I was out of support. Not much I can do. Can't make them buy it. Didn't really need it. These seem to be problems unrelated to simple programming or the...
Lock up and shuts down are frequent. System locks up religiously when I re select geometry. Issues on the pocket cycle in regards to rapid and feed planes. I own v18. I work with v27 at the day job....
Hi folks. Looking for any info on tapping h13. jave 60 pieces with 2 1/2-13 holes and 2 m10x1.5holes 1.25" deep. Cut tap or form? Coolant or oil? Have milling to do also and will be done on cnc....
Thanx for looking out. Pardon me I took a few days to get back to the thread.
I flicked the wrong switch on panel. Computer didn't like that. Had to reinstall surfcam I have 2015 r1. No lock ups yet. Havnt done much solids work yet. Just opened shop. Bobcad is the worst...
"Exception Access violation". Anyone see that message before?
you like surfcam better than espirit? that was an option for me. i was going to get bobcad being its cost a bit less. then tried one cnc. they changed it a lot. i have bobcad at day job. didnt...
can i ask what your using now?
i just found out my electrician wired it 208. what does that mean for the situation at hand?
and this could be part if not all of my problems? im getting drive faults also. im not great at all with electrical. looks like im going to have to call someone. i work during the day for corporate...
thank you for the info. a lot of good info and people here. im unsure what is meant by a sourcing machine. probably missing a lot. i had no idea that the machine came with a cts.
Thank you for te manual. The one I have was not tat thorough. I'm not using the pump. I just got machine and trying to start it up and decided to not use it at this time. Had a lot of set backs...
hi there i have a vm20 with a 8200 control with a cts unit that i am not using right now. trying to get the machine going and keep having a in feed hold message executed due to low pressure in the...