512,393 active members
2,529 visitors online
Register for free
Login

Search:

Type: Posts; User: mactec54

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 11 minute(s) ago.

  1. Re: ATC Spindle Assembly using a Chinese BT30 Spindle Cartridge

    I did not say you could not use them Face to Face it is your choice and your uneducated knowledge with Bearings that you would use this configuration, most machining centers today use Bearings like...
  2. Re: Making Z axis not lift all the way up everytime.

    Post the main line of code and I will correct it for you here is an example in inch


    G73G98X1.Y1.Z-.200R.1Q0.1F8.

    G98 will act with R value when the cycle is finished and lift the Z axis up by...
  3. Re: ATC Spindle Assembly using a Chinese BT30 Spindle Cartridge

    The NSK Tac series Bearings come in DB/DF/DT and can be installed in any orientation you want, including Back to Back if you are smart you buy universal, it all depends on design and how you want the...
  4. Replies
    2
    Views
    513

    Re: haas mini mill alarm 160 and 119

    This is a very old thread, how are you powering your machine
  5. Re: Avid Z stage, Clearpath motor and a 22 pound Spindle. Z drops when powered off.

    You could make a clamp that is solenoid operated or use a spring loaded air cylinder to clamp it, the spring load would clamp the shaft and the air cylinder would open it on power up

    The Emco...
  6. Re: ATC Spindle Assembly using a Chinese BT30 Spindle Cartridge

    This is a ER16 build I did for a Zone member some years ago, but the ER16 part was only modified I did not make that part, but do make complete Spindles if I need to, as well as special Bearings when...
  7. Re: ATC Spindle Assembly using a Chinese BT30 Spindle Cartridge

    Face to Face and Back to Back AC Bearing mounting need the same precession for mounting, there is no alignment forgiveness not sure how you would come up with this Bs

    Back to Back DB is a superior...
  8. Re: ATC Spindle Assembly using a Chinese BT30 Spindle Cartridge

    I have used the Emco Head as a 4th axis and as a milling head and it works very well, I normally build my own spindles though, the Emco head I used was from a parts machine I had so is still in use...
  9. Replies
    3
    Views
    19

    Re: Knocking sound when plunging

    No the material of the cutter will not affect what you are doing, can you do a video of it make the noise, there are many thing that could be causing this

    If you look at how the end of the cutter...
  10. Re: ATC Spindle Assembly using a Chinese BT30 Spindle Cartridge

    Should work well on your machine, the little Emco Mills have a nice 30 Taper spindle just like what you are going to build there is also a Taig one as well, these are expensive you can do it at a...
  11. Re: Got a CNC 3 years ago and gave up on it.

    Then if you started at Y0 then to return from Y-50 you should of just used Y0, From Y-50 is going to go Y50 =100 so you would go 50 past the start point
  12. Re: 6040 with AXBB controller problem connecting VFD

    Some confusion then on what you meant then, with post #7

    ( I was advising him with his vfd image he posted....not the axbb-e sample. Also the image confirms the connection was made like that...
  13. Re: Control Cabinet EMI RFI Glands and Clips

    You may find some clips that will work at a Hardware store, it's finding one that is the right size for your cable size is usually the problem, with some copper strip you can make your own just form...
  14. Re: Control Cabinet EMI RFI Glands and Clips

    Your metal cabinet will be Grounded so just inside the cabinet you can Ground the Shield if you can't find any cheap Glands for Shield Grounding, I will be making them soon as I found the same...
  15. Re: 6040 with AXBB controller problem connecting VFD

    The VFD Drive in the original connections was an output for +10v to a different Breakout Board which needed +10v for the PWM control the AXBB does not need that +10v connection from the VFD Drive
  16. Re: 6040 with AXBB controller problem connecting VFD

    Be carful with those connections the AXBB Manual shows a Yaskawa J-1000 VFD Connection, the VFD he has is not the same as a Yaskawa Drive and are mostly unbranded / named open board VFD Drives, in...
  17. Replies
    17
    Views
    70

    Re: WHAT IS THIS?!?!?

    That's the safety switch that these machines required
  18. Re: 6040 with AXBB controller problem connecting VFD

    You will have to see if the 0-10v out of the AXBB (AV1/Com ) is working by it's self so in MDI do a M3S12000 and see if you get around 5v output

    I'm not sure why you would be connecting +10v to a...
  19. Replies
    17
    Views
    70

    Re: WHAT IS THIS?!?!?

    No normally all there accessories all bolt or screwed in place some are just clipped on, it may not be for your machine Give Haas a call they may know, 2010 had a chip Guard for around the table it...
  20. Replies
    17
    Views
    70

    Re: WHAT IS THIS?!?!?

    Check to see if you can mount it on the side front of the machine for your Vice Handle

    Does your machine have a full enclosure?? most this age did not
  21. Re: How To Build A CNC System's Double Shielded Cable Assembly...

    Shield Grounding
  22. Replies
    2
    Views
    26

    Re: Feed Rates on a 300w Spindle.

    [QUOTE=ReliefArtist;2347472]Hello.

    I just purchased a 4040 CNC machine with a 300w spindle. Because the spindle is low-power, i'm worried about burning the motor out. Say if I wanted to make a...
  23. Re: 6090 mini atc cnc wood router machine for small size wood carving

    Same machine that is on there web site https://www.cncrouter-shop.com/pro/the-latest-6090-mini-cnc-router-with-linear-auto-tool-changer/

    It could well be 600 X 1200 but with the tool changer you...
  24. Replies
    8
    Views
    52

    Re: Haas MiniMill door interlock failure

    It's a built in safety feature you must of by passed it, or the machines that old may not of had it
  25. Re: Harvey / Helical putting mills down for 8 days and counting

    Ok make an offer to the company to be a reseller of there cutters here is a great opportunity for your company to change things, these so called suppliers are hopeless in most cases and never carry...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4