Mine was the X feedback cable
Its a dirty nasty job 19 years of coolant,chips and grease
Type: Posts; User: drogers
Mine was the X feedback cable
Its a dirty nasty job 19 years of coolant,chips and grease
Thanks all
I am up and running
Thank You All
I ordered a new cable from Fives should be here today I will let everyone know how it goes
When it errors out I first get and "39-47 Axes 'drive ready' signal missing" I then check the drive lights and have(Asuming from left to right PSR,VFS5,X,Y,Z) X is has two red lights from bottom...
Maver1ck you said "I have seen the limit switch cable short to ground" as in the XY OTR or TPA I/O cables not the 2 large Servo cables. I am in my I/Os but I do not know what to look for
Thanks
D
Maver1k
I cleaned the "X" switchs but I am having problems reaching the Y is there some trick? Of course this happens during a major rush job and the customer is not impressed.
Also why I...
Hello
I have an Arrow with the error message Axes 'drive ready' signal missing. I think its the cable chain under the table how do I get that out and where can I get new cables?
Thanks
David
I am even able to run the program with the error
Hello All
I have a Arrow 500 with A2100 control that I am getting the message "Error formatting message ID 0x270045" after bootup at first I thought it was the SSD but I am able to navigate to...
You may be on your overtravel switch in the Z
"I hear the contact breaker that goes to the PSR engage. It holds for a couple seconds and then disengages"
Does your control give a code at this point?
Is your air supply on?
Once per pocket error is most likely your drum proximity sensor
Good news today I pulled my "logic" board out of my original psr4/5 250 and put it into my ebay special and lo and behold the machine powers up and and can go 0 to 4000rpms no faults/errors.
I...
I thought people may enjoy this photo of my PSR
So I recieved my used psr4/5a today and carfully mounted it in the Arrow and when I power up the cabinet I have a red fault light on the power supply is that normal or is this DOA.
David
Mike
Thank you for the info
Hello
My Arrow 500 A2100 Power supply PSR4/5-250-7500 went up in smoke. Who rebuilds/exchanges these and will a Kollmogen PSR4/5A-250-7500 work?
Thanks
David
Looks like an ER collet holder
Meckardt55
It seems to be solved time will tell
Thanks for your help
Meckardt55
Sorry that I have not gotten back I had another machine down(Acra ADT450 with a Mitsubishi M50 no ladder!) and was working on it .I bought this from Amazon 6-36VDC 4mm Detecting...
The error is back I have the part on order should see it Tuesday
Thank You
Bob
What is Fives phone number?
Thanks
David
Mechardt55
I was reading my manual and found notes about tool change relays CR29 CR30 (Schrack# RTE24024 cost around $3.00) the previous owner must of had issues with these two so I replaced them...
When I turned the sensor in 1/2 a turn I noticed the cable is cracking. I can run the machine about 4 hours then errors start coming
How do I go about sourcing a new switch and cable (its starting to crack)
Merkardt55
I moved it in 1/2 a turn and have done at least 30 tool changes with no errors looks great so far.
Thank You
Hello All
I am having a once per pocket error it seems to be the same as
http://www.cnczone.com/forums/cincinnati-cnc/213808-cincinnati-1000-per-pocket-failure.html
How do you reach and...
babblefish
Hello friends good day someone could help me I need post processor for a cincinnati milacron mill with control acramatic 2100 I have to master cam 9 but I need it for the master x 5 or...
I am doing this on 8 parts(setups)
N50(MSG,T16 SPOT DRILL)
N60G80 G40 M09
N70G28
N80M06T16
N90M03 S2500 M08 F10.0
N100G0X0.98425 Y1.65354 Z0.5
N110G81 X0.98425Y1.65354Z-0.145 R0.2 F10.0