Search:

Hahaha i dont have time to write complete "do all"routines i just keep it simple

Sent from my SM-G960U using Tapatalk

Were you able to use and figure out the hex milling?

Sent from my SM-G960U using Tapatalk

What type of controler? What model? Mill or lathe? If lathe is there a bar feeder? Are there any other estop buttons that have been tripped that you didnt know about like on a chip conveyor or...

I always use the g101 i believe... turn od down to the corner to corner dimensions of your flat first i actually turn down below the corner to corner just to be safe but only around .02" or .5mm max....

thanks d kittin... great info... not sure i need the other info but wont know until i am able to change the tools. unfortunatly they (our wonderful maintenance dept.) tried the tool change and got...

came in the other morning to a crash into subspindle while program was using mtool. the crash caused the mtool drive to slip or lose its proper orientation to do a tool change. its about 40 degrees...

I sent you a message regarding your rfq... please reply back soon with a drawing and I can possibly make you a prototype using my material I have on hand.... we are located in st. Louis but I will be...

Send me a pm with print and I can get you a quote.... I deal in 100% composites from manufacture of the materials to making the product.

Sent from my SM-G930T using Tapatalk

I can sent part picture soon but not drawing... I can make you a simple drawing of id od in metric and send as well

Sent from my SM-G930T using Tapatalk

Send me code for the g23 I will attempt to use it until I can get the probe cycle. Thank you

Sent from my SM-G930T using Tapatalk

But it's not what I asked I asked for a renishaw probing cycle that would do this I already have the renishaw probe in the machine 4 ID OD offset calculations so yeah maybe programming a small tool...

Load monitor and G23 will not work. The material that cut doesn't create a load on the spindle or any of my XYZ CM axis. And I don't believe the G23 will work because the slots go all the way through...

Needing a sample program to search for a slot feature.

Process would be

Call oprobe1

G0 x4.3 z-1.2 c270.
Turn probe on
Probe feed in x into part searching for touch
If no touch feed out...

Here are tags for machine and transformerhttps://uploads.tapatalk-cdn.com/20170630/942dba57750696816e17331577e60272.jpghttps://uploads.tapatalk-cdn.com/20170630/c136a99c5508796ec580e31950af9f7c.jpg
...

I say double but yes a little more than double.... I looked at tag on transformer(had to remove several machine panels to get to it) and it says 130amps at 220 under the secondary column ....so.......

I have a quick question about a a transformer and amp draw....

220v into a 480v step up transformer does amp draw stay the same? Double? Or does it use half? I'm under the impression that it...

What's your fastest feed rate your machine can handle straight line and what the fastest it can go around a radius without leaving steps? If you haven't figured it out yet I can help you with speeds...

If I still have my program i will send it over as a reference if it will help anyone....

Sent from my SM-G930T using Tapatalk

Just use an adj boring head with smallest rad. You can and a nice slow feed.... smaller the rad. Of tool the less chatter and better finish you will have in cast alum.

Sent from my SM-G930T using...

Also you may try interlock release toggle switch inside of your cabinet if you have an alarm that will not go away because of an overtravel the machine locks itself to where it can't move in any...

I apologize I didn't see it was your turret that was the problem axis... can you post the entire alarm string since it's not available in the picture

Sent from my SM-G930T using Tapatalk

Your picture is not available for me to view but you should be able to power down the machine and move the ball screw manually into a position where the encoder can find its position again

Sent...

Also no problems with chips.... it's dust so recut is not an issue

Sent from my SM-G930T using Tapatalk

Imagine a ring that is what the part looks like 90 degree face on one side and 10 degree face on the other 4.375 od and 3.0 id.... starts out as a 4.625 x 4.625 x .625 thick square blank loaded in...

My left elbow.... right elbow was last year lol this is actually a running program that runs flawlessly making 1000 parts per month. You are sort of correct in saying grinding.... I work with...

Currently in the process of training my minion operator (button pusher) my okuma lb3000exII myw. I have been using diamond abrasive cutters and rec diamond cut routers with excellent success and...

I completely agree.... I work for a 70 million dollar per year company and I am the only programmer for our okuma lb3000exII MYW been working with our cad team to try to take some of the programming...

I am in the market for a CNC lathe with at least a 4.4 bar capacity with live tooling. I currently have an okuma lb3000 ex2 with the Big Bore Kit but my Max Capacity is 4.3. Would love to stay with...