Hi
Here is picture of UB1., Can you mark what you are talking about. "" just connected the override limit to the pins, and then i have connected that pin to reset in UCCNC ""
UB1 doesn't...
Type: Posts; User: akihiko
Hi
Here is picture of UB1., Can you mark what you are talking about. "" just connected the override limit to the pins, and then i have connected that pin to reset in UCCNC ""
UB1 doesn't...
Ok. would share how did you wire it up... draw diagram.
right now hive mines working, but only the yellow/green on X105 and 0V Pin/5 and I/O Port1, And work perfect. But that it can also be...
hello,
Looking for help to Setup 4 wire automatic tool sensor to UB1. I seen people on Youtube with it setup on UB1, UCCNC Software. Didn't show how it was setup/connected.
The only wiring i...
No, its for 6040Z frame.
Hello, CNC Nuts.
This Thread is to help:. Newbies, CNC Hobbies.
Feel free to post. Ideas, Suggestion. Recommendations, Possibilities. Creative.
Stepper Motor's Nema 17, 23,24,34,42. &...
(Spelling correction)
""" First cut is accurate second cut is not.
Have tried three different samples each of the samples first cut 30.50mm and after the final cut 34.29mm A perfect cut. On...
ok, thanks
upload now
ok. i did .f3d under autodesk foolder.,
which one, theres a list .f3d file about 30 file .
Sorry, Don'r mean to sound stupid. how to locate f3d file. please explain with more detail.
thanks
ok,
i upload it as rar file
hey,
I seem to have some serious problem making some cuts with using 360.
First cut is accurate second cut is not.
I have tried three different samples each of the samples first cut 30.50mm...
in side the VFD, jumper and posts
Like this..
like i said before, CNC software dosn't work right, all 4 jumpers are set to left side thats of VFD by default factory, Now move the jumpers to the right side if want to control it with the cnc...
Hey,
i hive rebuild my 6040Z from groud up. The JP-3163B controller board its not a good controller. it didn't work most of the time i used, one problem after other. and the VFD that came with it....
hey
Your reply from : Stepper motor forums (( Hi. did you start the frequency inverter with the PC? Did you do that with the wiring? I have opened a thread for this to help others as well.))
...
Just fine out that (STEPPERONLINE 1 Axis Closed Loop Stepper Motor Kit 2.0Nm 1000CPR Nema 23 Closed Loop Stepper Motor+0-7A 24-50VDC Stepper Driver+2 Extension Cable)
It only a 2.0 283.28...
hey,
I'm Thinking of Upgrading my Stepper Motor's to --> Closed Loop Stepper Motor.
I'm looking at two differen Closed Loop Stepper Motor.
1. STEPPERONLINE 1 Axis Closed Loop Stepper Motor...
PS.
i guess i can't use this tool, Unless i trim the shaft down to 12mm, to make fit ER20 collet #12.
Any ideas
hey,
i finally finished my upgrade. Now i need to trim the surface. from 0.085 to 0.000 any tool recommented to this job.
The material i used to do this project:
1/2 steel plate 19x30
18,...
19" = X = 482.7mm
29.5" = Y = 647.7mm
5.5" = Z =139.7mm
So just find out that my 6040Z it's lettle different from other 6040 them other 6040z. The X Axis it's wider. Where other it about...
X axis 1605 ballscrew
Y axis 1605 ballscrew
Z axis 1605 ballscrew
im sorry didn't understand -> (What is the pitch of the screws?) what screws?
so her is the video: pay attention @ 1:10 first run, And second run @ 4:11
Even though the cut came out clean....
it set MM
and YES backlash dis-enable
Here is pics my setting in UCCNC AXIS SETUP.
By way this is first time leaning CNC. Im leaning as go alone...
You dont hear the stepper whining. Also just about around the third cut it start to hesitate. And them it correct it self.
ill will upload another video so can hear and see closer.
DIP SW on...
check out what doing when its cutting,
https://www.youtube.com/watch?v=KR5CnwVmLSU
The reason I change to these motors, because the previous motors that came with the 6040 was Half the size of these guys, they had less torque power @ 24v supply. It was recommended if I’m going to...
Sorry, i wasn't paying attention to the question at first. here's what i know so far about these motor's.
NEMA 23 Stepper Motor
Model: 23HS9430B
Step angel:18°
Motor Length:115mm
Rate...
So this my new Spindle 2.2k 220v 8A 24000 400Hz 80mm.
i had change the support plate of spindle 1/4" to 1/2" so spindle can hive enough clearance, When it come up Stepper motor Z azis...
After the adjustment and realignment to work area.
That's the way they came from LONGSMotor, they sold them with 36v power supply. when i email they support team.( they stated, that's configurtion for those stepper drive and Motor's each driver and...