The radius in the tool table is .0001, we commonly use WEAR type CC. so we program with the radius of the tool taken into account and only add the delta needed. Typicity is .0005-.002 is all that is...
Type: Posts; User: ou812
The radius in the tool table is .0001, we commonly use WEAR type CC. so we program with the radius of the tool taken into account and only add the delta needed. Typicity is .0005-.002 is all that is...
I hope someone here can help. I am trying to use incremental sub-programs. However, I am getting a PLANE WRONGLY DEFINED 7628 error on line # 7665. I am trying to turn CC in a straight line. No...
We have 3 older Mikron Vario 600 machines with the iTnc530 control ( Table/Table config ) and one of them just the board for the spindle probe. I currently have a pivot/rotation issue and need to...
thank you for the help. Have a great day.
Also, is these a command goe sending a machine to axis extent? Like a Fanuc G91 G28 Z0
clearance is no issue. I just want to ensure it doesn't cancel any tool length information.
If i command a M140 after the TOOL CALL will it create an issues? I would like to do this to make sure there is Z retract before rotary axis re-positioning on restarts.
*B0 C0 ROUGH WAVE GUIDE 1...
***** I found my answer. APT post software to process this code. *****
Ok,I need some help from the UG/NX guru's here. I was sent CLS files for a project and not sure how to post them for machine...
Hi, I recently switched from UG NX4 to SolidWorks 2009. I some how dragged the main toolbar from the top and can't get it to snap back. They only place I can get it to locate is the right side....
We have Mits horizontals with 520 control. We have to run our code like this
T1 (WORKING TOOL)
T2 M6 (T2 PRECALL NEXT TOOL)
.
.
.
.
It was pretty annoying it will alarm out if you call the...
I had a similar problem on an 18i-MB. It was fitted with one of the new Direct Drive Rotary 4th axis capable of 250 RPM. I ended up programming in metric to get past the 4 didn't issue. Fanuc said...
Poss31,
In the past I have contacted the Hardinge UK office, they are the old Bridgeport. They used to do all the engineering there. Ask for Sean Briars or Darren Clarke both good guys. I once...
The only time I have ever used a G11 is when changing parameters or tool life management. Neither I want left open for accidental adjustments by a program or operators.
As for tool or work...
Gwarble,
I'm a former Apps engineer for Hardinge/Bridgeport. I had a customer down Jersey way. He had Mori's with custom M code similar to your issues. I contacted Fanuc and they stated the that...
We used to edit the M61&M62 macro for pallet changes. We added a statement like below. This way we could set-up safeguard commands to ensure the correct program was run on the right pallet.
Some...
now there is the fly in the ointment. I don't think you can do a spiral set up with the RS-232 connection. I believe you can do it as a M code only as you described.
Sorry, I got nothing else....
Tom,
Most Haas mills allow you to hook up an their indexer as a auxiliary axis. You still need the box and straight thru RS-232 cable. On the back of the mill there should be 2 RS-232 ports, top...
We are in the the process of adding a spindle & tool probe to a older Haas VF3. we have buy the whole system. about 7-8K. Renishaw OMP40 & TS27R
I just did some internal training for back-up...
Kevbo,
You can toggle parameters with a G10. This is explained in the fanuc programming manual.
OU812
G10L50; Parameter entry mode setting
N_R_; For parameters other than the axis type...
Alright calling all Haas guru's....We have a Haas VF3 with a full 4th and a indexer 5th. Machine config, we have a HRT210 in-line with the X axis (index only, run by the Haas box) and a 5C bolted to...
Not sure about other machines using this holder, but I have had good luck with Parlec making specials. They have never turned down a quote.
Hi all,
I just stated using NX4. I'm a long time Mastecam user and hoping I can find a few of the long time NX users here willing to help. I'm currently going thru CAST and finding it leaves a bit...