Search:

Hello all,
I need a little help please. I just purchased a Kiwa Exelcenter 4 L with the Fanuc 10M controller. It doesn't come with any documentation. I need service manual and operators manual for...

Hello all,
I recently received a MC 760. It came shipped with the oil chiller removed.
I need a little help from someone who has one of these. The 2 oil lines coming from the machine are...

I purchased a used Marathon/Exell turning center that has a vdi 50 style turret. Some of the clamp screws, wedges and hollow coolant line up bushings are missing from about 4 stations. it has a 12...

I need to remove the Y axis ballscrew from a Matsuura MC-760 vertical mc. Has anyone done this? Where to start and tips appreciated.
Thanks,
Keith

Hello all,
I recently acquired a used Cincinnati Talon 210 with the Accramatic 850SX. The display I can barely read so I got a lcd monitor kit to replace it with. I'm ready to change out screens and...

Hello,
I am right now getting ready to replace the coupling. Did you have to purchase from Methods or was a replacement part available locally? I was told it was a Lovejoy type coupling by someone...

I have a lathe with 10 TF control. I bought it used and have been using rs 232 to store programs. Something went wrong and it no longer will accept rs232. I tried different cables and still does not...

Thanks Al,
I looked furthur in the machine drawings and see that there is a specific Y address given for them. Gonna go try it now.
Thanks again

I have a Fanuc 10TF control. I know you can watch the inputs on the diagnostic screen and the machine prints tell me which ones are which. But can I watch the outputs on another diag, screen. I am...

I edited the program to put a G00 in the same block as T0101 and it started working ok. I don't know why it worked before this.

Here is the code below. This is the first job I have run on this machine so I am sure it needs some editing. But like I said before it was working fine before and all of the sudden I get the alarm...

I have a Warner Swasey WSU 12 w/ fanuc 10tf control. Everything was going good on it untill out of the blue an alarm "PS187 FEED ZERO(COMMAND)"
comes up. IT alarms when the turret starts to index....

I finally got my W&S WSU 12 running on a job and had the surprise of my life right at the start. It was in a rough turning pass and I needed to stop it so I pushed the feed Hold button. The feed...

I have an oilfield threaded flangewe are machining that is killing me on the 4-1/8" 3 pitch external rh acme thread. I tried running with a 54 series on edge insert but about 3/4 way into the thread...

Thanks everyone for the replies.
I checked the cable and all is ok except like you mentioned Dan. There is no continuity from 9 pin end pin # 7 to 25 pin end pin# 5. Also pins 4 and 5 are not...

Hello,
Can anyone help me please? I have a WSU 12 with a GN 10TF control. I bought a communication kit from a guy on eBay for RS232 hookup. I set machine parameters per his instructions and can only...

I have just the opposite problem with a 10tf. can send to control but can't receive from control w/ tereterm. control keeps flashing "punch" but no data is sent to pc.

I found out that there are other parameters to change also. CMR, DMR and GRD. I can locate CMR @ # 1820 but the others I can't locate. Thanks

PWE ? Please explain. I am new to this control. Thanks,Keith

All bits across param #1006 are 0's. Bit #'s are read from right to left starting w/ 0 correct? 0-7 from R to L ? I need to see if there is any others that need changing also. Thanks. Keith

I think my W&S WSU 12 is set fot radius programming. I am used to diameter programming on our Tsugami with a 6T control. The WSU has a 10TF controller. Is there a parameter to change or a code to put...

if you use a flame on dried superglue then the fumes created contain cyanide. don't breath them.

I need help getting started with my new WSU 12. It has a Fanuc 10TF control. Up untill now I have been setting up and programming our other lathe with a 6T control. You have to use g50's in the...

Hello,
Could you send that info to me also. Will it be the same for a 10t control. I have both 6 and 10 that I want to use a pc with.
Thanks,
Keith

Ok. I got past the soft overtravel problem. Now another problem has arrived. It seems like one step forward and 2 back with this machine.
This is a W&S WSU with a Fanuc 10TF control. The monitor...

Al,
I did a search here for IPL and this past thread came up:
http://www.cnczone.com/forums/showthread.php?t=6252

I am confused now. If I push button 7 and 9 will the parameters and everything...

I need some help please. My lathe with a Fanuc 10TF control won't reference in X. I get a +X overtravel(SOFT) error message when I try to reference it. It started this after I powered it down and...

Thank you for the example. There are some G codes in it I am not familiar with. G54-G55. I assume these are work shift offsets? I ordered a book for my 10TF and it has the conversational programming...

Could someone please post a couple of simple lathe programs in Fanuc 10T.
I have been programming a Tsugami Mercury with a 6T for years and I now have another lathe to use only it has a 10TF. I...

I went there but noting on fanuc.
Thanks