584,842 active members*
4,196 visitors online*
Register for free
Login

Search:

Type: Posts; User: Mikey4865

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    792

    Coolant thru Tool Holder Search

    Hi all,

    I recently got a high pressure pump hooked up to our Swiss but now have the troubling task of finding tool holders.
    I use CNMG 331/332 on pretty much every part we run. Anyone have any...
  2. Replies
    2
    Views
    2,720

    Re: Mori Seiki ZL200 SMC Part Catcher Speed

    PMM Parameter #40
    Worked pretty well. Now only about 10% of the parts fall into the chip conveyor (Large part so none are lost).
    5 inch part sometimes just gets thrown when cutting off even at...
  3. Replies
    2
    Views
    2,720

    Mori Seiki ZL200 SMC Part Catcher Speed

    Hi all,

    I am having an issue with the part catcher moving way to fast when retracting back to home position. Anyone have any thoughts on how to slow the speed down? I could not seem to find any...
  4. Replies
    1
    Views
    1,051

    Mori Seiki ZL 200 Part Catcher Speed

    Hi all,

    I am having an issue with the part catcher moving way to fast when retracting back to home position. Anyone have any thoughts on how to slow the speed down? I could not seem to find any...
  5. Replies
    7
    Views
    2,177

    Re: CNC Swiss Sanding

    Live tooling isnt the issue, its the orientation of the part being so long that makes it difficult. I'll let you know how it goes!

    Thank you
  6. Replies
    7
    Views
    2,177

    Re: CNC Swiss Sanding

    Tolerance on the OD is 0.005 so holding a size it not needed with the wheel. Just something to blend the mismatch so a rough finish is OK (we currently use 180 grit sand paper to blend the diameter...
  7. Replies
    7
    Views
    2,177

    Re: CNC Swiss Sanding

    turned od ranging from 3/16 to 1/4, lengths range from 2.5 to 5 inches and there is a large ear on each end.

    Thanks for your help!
  8. Replies
    4
    Views
    1,598

    Re: CNC Swiss Sanding

    Long inside diameter has minor mismatch that is currently sanded by hand with 180 grit sand paper.
    Sometimes chips are loosely hanging from the inside diameter so the wheel would need to be able to...
  9. Replies
    4
    Views
    1,598

    Re: CNC Swiss Sanding

    Anyone try a Silicon Carbide wheel on 400 stainless steel?
  10. Replies
    4
    Views
    1,598

    CNC Swiss Sanding

    Hi All,

    I am currently using a CNC Swiss to make parts that range from 3-8 inches long (so can't pull back into the guide bushing and can't run without guide bushing). We currently take the parts...
  11. Replies
    7
    Views
    2,177

    CNC Swiss Sanding

    Hi All,

    I am currently using a CNC Swiss to make parts that range from 3-8 inches long (so can't pull back into the guide bushing and can't run without guide bushing). We currently take the parts...
  12. Replies
    2
    Views
    1,114

    3/8 -16 UNC -2A Thread on L-605 Material

    I have a part that needs a 3/8 -16 UNC -2A Thread about an inch long. The overall on the part is about 4 inches. I have tried single point threading, and am currently sending the parts out to be roll...
  13. Replies
    13
    Views
    6,089

    Turns out M54 right before an M99 is what it...

    Turns out M54 right before an M99 is what it needed. But apparently the M30 code initiates the barfeeder, so that now has to be changed since we need to use M99 to run continuous.

    Thanks for all...
  14. Replies
    13
    Views
    6,089

    Ill give that a try, the service guy should be in...

    Ill give that a try, the service guy should be in today some time ill post if anything changes.
  15. Replies
    13
    Views
    6,089

    6710 is set to M54 I had set the parts...

    6710 is set to M54

    I had set the parts required to 5 and it will count the parts made but it wont stopat 5 it will keep going, 6 ,7 ,8 until the bar is done.
  16. Replies
    13
    Views
    6,089

    Yes, parts required is set and parts count is 0....

    Yes, parts required is set and parts count is 0. I have tried the following codes at the end of the program.

    M30 at the end of program.

    M99 at end of program.

    M54 and M99 at end of program.
  17. Replies
    13
    Views
    6,089

    I have M99 at the bottom and it runs continuous...

    I have M99 at the bottom and it runs continuous but it still disregards the parts counter. It will count each part but it will not stop until the machine alarms out when it finishes the bar. Ideally...
  18. Replies
    13
    Views
    6,089

    Doosan Puma 2100SY

    Anyone have any trouble running with the parts counter? It registers each part but will not run continuous.

    Ideas?


    Thanks,

    -Mike
  19. Replies
    2
    Views
    614

    Need to increase run time!

    Hello,

    I am trying to increase the time cycle
    on my current job. I am using a Hanwha XD35 Swiss
    CNC Machine. My current time cycle is 3 min 35 seconds (Main spindle)
    and 2 min 5 seconds (Sub...
  20. Replies
    4
    Views
    905

    Ahh I see, thank you very much.

    Ahh I see, thank you very much.
  21. Replies
    4
    Views
    905

    Sorry, I mistyped then. I do have BobCAD - CAM V24

    Sorry, I mistyped then. I do have BobCAD - CAM V24
  22. Replies
    1
    Views
    688

    Cannot Integrate BoBCAD

    I have bobcad and solidworks downloaded V24 and 2012 solidworks, and when I open solidworks and go to the addins section I cannot find BobCAD. Am I missing a step?
  23. Replies
    4
    Views
    905

    Solidworks Add-In...?

    Hello,
    My issue is simple... I have loaded BoBCAD V24 and Solidworks 2012 already. When I open Solidworks and click Add-Ins, BobCAD is not there.
  24. I could see some orange but more yellow, it comes...

    I could see some orange but more yellow, it comes of with some solvent and a razor blade but it just takes to damn long.
  25. Sounds good I'll give it a shot tomorrow and let...

    Sounds good I'll give it a shot tomorrow and let you know how it works.
  26. How can I remove a thin Layer of Silicone off of Aluminum

    Hello,

    I have a many sheets of aluminum about .050 inches thick,12 in x 12 in.
    There is a thin layer of Silicone on it and I need to remove it without damaging the aluminum material underneath....
Results 1 to 26 of 26