Search:

I have a Powermax 85 and the amp dial no longer works so it is stuck on 45 amps and I can't change it.

The Dial spins freely just does nothing. It has been sensative for years but now it just no...

I got a response from Esprit and thought I would post it here for reference.

"To answer your post processor questions, we used to have open .asc post processors where you and me could edit them,...

Hi,

When you guys get Esprit does it not come with the Post processor required for your machines ? I see lots of guys with Esprit chassing Post processor support and was under the impression that...

Long shot but did you ever find one ? I need one for a 145G18C and came up with this post

Well we are into 2020 now and the Arclight CNC is still going strong and I have lost count of the number of sheets she has cut. Only issue I have at the moment is it looks like my Height Control may...

Yep still have, still use it every day and still happy with it. I have the router and use it occasionally but it makes a mess and doesn't mix well with water or steel. I would buy one again without...

Hi Alan,

I am in San Diego 92082.

Good to hear you got the Arclight I am sure you will continue to be happy with it I know even after 3 years of abuse .. I mean fabricator use I am still happy...

Having had a PlasmaCam , a Torhcmate and now an Acrlight CNC I would go Acrlight again in a minute if I needed to start again. The ability to roll it out of the truck and start cutting in a few...

I know thread is a bit old but thought I would comment. 95% off the stuff I cut gets used without any further clean up unless I am Tig welding it. The amount of dross you get is very minimal if at...

I would think the problem will be with your driver software. What do you do with it after you export from SheetCam as a Tool Path ? In the ArcLight CNC I open it up in Mach3 and imprt the ToolPath....

See if you can get a hold of Jim Colt, he is the Hypertherm Man and has a Plasma Cam. My Arclight came with the Powermax hooked up through the factory Interface Board so no help there. Jim hangs out...

ok so with the shop clean and the days ticking I needed to get cracking. 1st thing I had to do was get the chassis level and get the front beam aligned so I could sling the body on and check how my...

Yeah Ok I do the layers in SheetCam not external.

The water is low for one reason SOCAL lol it goes from full to that in a about a week and if I know I am cutting timber or doing minimal cutting...

Hi G, I am a little confused in relation to you saying you created a drawing that has the pattern on a separate layer to the plasma. I say this because of the word create. Do you mean you made a DXF...

Ok so I have read a lot of posts and seen some great examples of what people get up to. With that in mind I thought I would take some time to details a few of our projects and show how much easier...

If you are serious about getting one I would STRONGLY recommend if you can going to visit ArcLight and do their training. I did it after I had the table for a while and I was amazed at how much I had...

After more than 2 years of plenty of cutting, playing and thankfully making money I am pleased to report that I am still more than happy with the ArcLight CNC Table and the support I have received...

You could mount it easy enough and the control will work so I don't see why not. As far as I know ArcLight don't have a hand torch holder and personally I would never go back to a hand torch. I leave...

Well it has been almost 2 years with an ArcLight now and I have burned through literally hundreds of sheets of material from 1mm to 20mm thick without issues.

After doing the training with Scott...

http://www.youtube.com/watch?v=z3IHzgEEJPA

Well it had been a few more months and many more sheets of steel and alloy. I have still had no issues to speak of and am very happy with the table....

I used the router and it works fine. It is a learning curve from the Plasma as at the end of the day I am a steel guy lol. The software is easy to use and the Arclight Profile and training takes care...

I have had no issues with the water table, it even comes stock with a drain valve should you need it. I never adjust the water level as such. I will add water but that is due to evaporation and...

Well it has been a while time for an update.

Firstly Scoot and the Boys at ArcLight have been exceptional with Customer service and follow up. I would go as far as to say they have gone well...

Funnily enough I have the Router, Plate Marker and Tube Notcher Attachment for it so yeah I will be chipping wood :rolleyes:

Hi,

Haveing been down a few paths over the years I wish I had just bought an ArcLight in the first place, granted they didn't exist when I started out in CNC Plasma but you get what I mean.

My...

Wow thanks for that Tom, I have only just gotten back to this but after a few minutes on the phone with Scott yesterday the table is now fullt functional and after doing some callibration testing I...

damn it looks small in that room, the room is 12ft deep and she fills it from wall to wall :)

I was going to start a build thread but I realised that my ArcPro 1200 5x10 CNC Plasma was delivered Turn Key so I guess it is more of a review.

I have seen a few people asking about the machines...

I have one, I will start a thread for you

Quick update and I will post more pics and info in my own thread over the following weeks. My ArcPro 12000 arrived today without issue. All looks to be sweet and I can't wait to plug it in and get it...