Email sent
G28Machining.com
Sent from my SM-G955U using Tapatalk
Type: Posts; User: cooperjm
Email sent
G28Machining.com
Sent from my SM-G955U using Tapatalk
please contact me at [email protected]
Sent from my SM-G955U using Tapatalk
The post needs to be reformatted to work with the canned cycle for that controller. There is also a deep drilling cycle that is a macro program of the controller that works really well.
I have a...
Yes I have a post that I'm using with the lathe it works okay. It does not do the drilling Cycles. That is just something that I've lived with. Have not spent the time to fix it
Sent from my...
Bearings are not pressed. Not sure about indicating it
Sent from my SM-G955U using Tapatalk
If I remember correctly you're going to have to at least Slide the screw out far enough to get the bearings off the end.
Sent from my SM-G955U using Tapatalk
We are near the other LA, Lower Alabama. If you could post the file we can send you a quote.
[email protected]
I am using the connector on the right rear of the machine. That is where the schematic led me to..
If you look at the schematic at the bottom of the AUF Card you will see HAAS Option. That is the...
I am using a Haas indexer with mine. The M51 command sends the signal to the cannon plug on the RT Rear of the machine. This will only do 3+1 machining.
Todd
I have sent you an email.
G28 Machining.com
Mike Cooper
Your private messages are turned off.
Sent from my SM-G955U using Tapatalk
Hello
Please send your part files to receive a quote. We have a few anodizers that provide reliable service.
We are located in the USA, South Georgia.
Email [email protected]
Mike...
Please send your drawings to
[email protected]
We can help with CAD and and machining.
Mike Cooper
Sent from my SM-G955U using Tapatalk
I agree. I am not sure which one would be causing it though.
The images below show the issue I am having. This is on a TorqCut22. When traveling in the X direction there are heavy/deep tool marks in the part. Both directions were cut with the same conditions....
I rebuilt the rotac with the seal kit. All the seals inside were crumbling that was the main issue. The rotac can be removed by only removing the motor.
Currently it's shifts gears 95% of the...
Are you located in the US? Will you be accepting quotes from other countries?
I am interested in quoting your job but will not be competitive with quotes from China.
If you're interested please...
Send the dxf to [email protected]
Sent from my SM-G955U using Tapatalk
Apologize for the confusion. I never said I did the conversion. I had a cat 40 tool that I used in My BT machine. I change that to out by hand. I do not have the tool anymore but I kept the pull...
Marty
I just spent 30 minutes looking for those to pull studs that I have. I cannot locate them at this time. I do apologize.
If you go look up the taper length 4bt 40 compared to a cat 40 that...
Yes. Dimensions C will be shorter for the CT tool holder.
Sent from my SM-G955U using Tapatalk
No, that is not it. It looks just like the. but it has 5/8 11 threads on it. It is also shorter then the BT pull stud. I will get you a picture and dimensions when I get home this evening.
Sent...
I have some. I can send you pictures an dimensions next week.
Sent from my SM-G955U using Tapatalk
Couple weeks ago. I bought a whole Carousel worth of segments..
Sent from my SM-G955U using Tapatalk
If you buy all 22 segments from EMI, they're around $25 each.
Sent from my SM-G955U using Tapatalk
You also have to change the tool change height. You need a different pull stud for the ct40 also.
Sent from my SM-G955U using Tapatalk
Please send the fusion file to [email protected].
Thank you
Sent from my SM-G955U using Tapatalk
I have read the suggestions that I have found on ww and on this form. At this point it is a neutral and will not shift either way. I have already tried the manual shifting method that was described...
Have a Torq cut 22 I'm trying to revive. I bought it in as is Parts only condition. So far everything has come alive and started working except for the gear changing. I have another Torq cut but it...
Do you have a drawing of the item? You can send it to [email protected].
Sent from my SM-G955U using Tapatalk