yes pictures
and im subscribing
Type: Posts; User: jeep534
yes pictures
and im subscribing
This is unbeleivably helpful
Thank You
archie
John,
Thank You
The boards woke up by changing the power wires. Now to get them working with the software.
archie
Bubba, Thank you ,
Arturo sent me this one already. I have +5 volts connected to the board but it will not wake up for some reason.
could it be a jumper setting
archie
I have a older C11G rev5.4 breakout board it has a en (enable) pin and a connection right beside it labeled +5 volts I am wondering how to hook it up there is no 5 volts on the 5 volt connector. I...
I have a new old CllG and a eithernet smoothetepprer and a Viper 200 I have the High voltage supply for the viper it looks like i need a seperate isolated supply for the viper. reading the...
I sent you a pm with my contact info
archie
Larry,
I have had my viper 200 drive for a while (nov 2012) and I am getting ready to bring it up and test it for the first time. (yeh i know the warranty has ran out lol) I don't have a...
Larry,
which US digital encoder would you recommend
Thank You
archie
Archie's first cnc machine Bridgeport R2E4 Boss 9 to Mach 3
and yes I have been messing with this thing since 2008
Thank You
archie
I am retrofitting a Bridgeport Boss R2E4 CNC Mill and I am wondering what size of AC servo motors I need to replace the old DC servo motors. this KW sizing has me all confused.....
Bridgeport...
Ill bite... what you are trying to do is not possible or how things are done. the loop is closed back to the drive not mach3 there should be an error signal coming out of the drives for them to tell...
Thank you
archie
Larry,
Is this what I need to assemble the cables and connetors I purchased.
Molex Style Crimp Tool Wiring Harness Crimping Crimper Open Barrel 14 24 AWG | eBay
Thank You
archie
wow too cool
archie =) =) =)
Greenbuggy so where are you located.... I am working The I-80 corridor. here is my build thread
Archie's first cnc machine Bridgeport R2E4 Boss 9 to Mach 3
Happy Hunting
archie =) =) =)
cell towers for AT&T we are working along I-80 I do have plenty of weekend time. I tried to find century on streets and trips no Go so where is it exactly.
I am currently working in the state where are you located.
archie =) =) =)
Those look really cool, what would that be in american money.
Thank You
arche =) =) =)
this is an old post. have you made any headway. I have the same issue which I have not gotten worked out as of yet. I am working on a Bridgeport R2E4 which is basically the same mill ( head...
I really like larkin and his drives. they are really nice however, I don't believe his breakeout board has provisions for the safety charge pump or speed control of the VFD (other than just and on...
My Build thread is here.
Archie's first cnc machine Bridgeport R2E4 Boss 9 to Mach 3
I started some time ago. If I were starting today I would use the larkin drives and a CNC4PC C32 BOB and the...
Thank You AL. for some reason the zone is not notifying me when a reply is posted. yes the question was about the encoder I am trying to hook the BEI encoders to a Larkin Viper 200F and the mill...
Paul, how are things going.
do you still smell bad.
archie =) =) =)
KC8YND
understanding this is an old thread i am in search of such aa form cutter.
archie =) =) =)
I am working through the same process. all in all steel is heavier in mass than aluminum. I would think thin gauge steel of the same outside dimensions is lighter than 8020 and easier to weld. also...
Thank You
archie =) =) =)
what is the travel on the slide.
Thank you
archie =) =) =)
First of all what an impressive build. many ideas i would like to appropriate ;)
I have tried to go to the link for your other build but I think the link is broken.
My question is what are you...
I have a Bridgeport series 1 R2E4 with Powertron servos and bei encoders I recently purchased a viper 200 drive and have been scratching my head as to how to connect it to the existing wiring going...