584,850 active members*
4,428 visitors online*
Register for free
Login

Search:

Type: Posts; User: bobecm

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    11,747

    Re: MC-4VA Servo Timing Board TB2 OSP 5000

    Hello mapemera

    Have you solved the rumbling problem with replacing TB2?
    Thanks.
  2. Replies
    2
    Views
    618

    Yes, machine has come from UK in Serbia and...

    Yes,
    machine has come from UK in Serbia and original manufacturer is from Spain. Manufacturing quality of boards is quiet good but there is not any name of manufacturer, just serial (PCB...
  3. Replies
    2
    Views
    618

    Servo driver and power supply

    181040181039181041

    Hello gays

    Is there anybody who can recognize boards from attachments. This is power supply board and one of three servo boards. I would be grateful if someone could give...
  4. Replies
    0
    Views
    1,202

    MICON cnc controller at Kondia K76

    Hello :wave:
    Is there any who meet Kondia K76 machine with Micon cnc controller ? My problem in fact is servo controller (3 axes board plus power board) from unknown manufacturer. Please for any...
  5. Replies
    11
    Views
    4,003

    It is probably problem with monitor only

    It is probably problem with monitor only
  6. Replies
    11
    Views
    4,003

    Ideas of Al The Man are preaty good. Also , what...

    Ideas of Al The Man are preaty good. Also , what about indication at LED's . RF and RS are foer enable, MR1 and MR2 for direction, BB - ready etc. BS indicate fault conditions.
  7. Replies
    0
    Views
    897

    SL25A500 with Fanuc15TF control

    Hi gay's
    Is there anybody who can help me about analisys I/O board M022 for Operation Panel. Problem is machine behavior: without any operator action mode machine are changed, manual spindle speed...
  8. Replies
    4
    Views
    1,608

    Is there any recomendation for commercialy BTR....

    Is there any recomendation for commercialy BTR. Some low cost solution?
  9. Replies
    4
    Views
    1,608

    LC30/OSP3000 to PC

    Hi gays
    Is there anybadi who knows way to use connector with remarks RS232 at interface PCB at control system OSP3000. And way to load part program from PC to control . Thanks
  10. Thread: Glentek GA4568E

    by bobecm
    Replies
    0
    Views
    1,202

    Glentek GA4568E

    Hi guys
    Is there everybody who now why hapaned with Glentek GA4568E Z axis amplifier on VMC 904-1. Z axis dont move, and on "fault" pin (No. 6) of amplifier I measure 5.5 V. At X and Y amplifiers...
  11. Replies
    5
    Views
    1,459

    Thank you Andy I will try this ASAP and write...

    Thank you Andy
    I will try this ASAP and write result to you.
  12. Replies
    0
    Views
    1,239

    Bus error mesage at Fanuc 15TF

    Hello
    Are there any comment about this error during butting conntrol Fanuc 15 on
    SL-25 lathe. Is there "medicine" for this behavior?
  13. Replies
    11
    Views
    4,756

    Hello ndp I'm prety sure that you have some...

    Hello ndp
    I'm prety sure that you have some proximity switch for tool position codding bad, (or unadjusted, if you lucky guy) and an original spare is wright solution. I was tryed in past time...
  14. Replies
    5
    Views
    1,314

    Hello ncmas Can you sending me wiring and...

    Hello ncmas
    Can you sending me wiring and parameter's detail's please for GE control. I have not DNC control available at the moment, but I hope that i can realise file transfer. Am I wrighte or...
  15. Replies
    5
    Views
    1,459

    Hello Ozgurm If you find solution, share it wit...

    Hello Ozgurm
    If you find solution, share it wit us , please. Wiring and parameter detail's. Thanks
  16. Replies
    0
    Views
    976

    Backlash compensation at GE MC2000

    Hi guy's
    Is there anybody who now way to compensate axes backlash in General Electric MC2000 control. Machine is Wadkin VMC 6-4. Where I can find parameter list and haw I can edit parameters?...
Results 1 to 16 of 16