Search:

I'm aware of that. They haven't decided on which control to purchase as of yet, but they already have the robot they want to integrate. I was looking to see if anyone had a ladder backup from each...

I'm looking for a ladder diagram for a 4020 machine with an 0i-MC and an 18i-MB. I have a project coming up doing an integration and would like the FAPT files for reference to start building my...

Keep in mind that after two semesters you may not be up to par with what the "other workers comments" consider to be someone who truely knows the ins and outs.

Some of the other guys on here have...

problem solved.

Stevo,

Even if you delete the message in the message listing the machine will still stop once the alarm condition is met--You just won't have a message describing why it stopped; and the message...

According to the documentation I have, G74 is an option that has to be purchased.

What exactly are you having problems with? How to call up a tool and get it to count life in the program, or setting up the tool life page?

It shouldn't affect the ATC since you said it travels with the Z. I'm assuming when you do a t/c you just tell it to go to Z 0 and change tools.

I'm not familiar enough with you machine to know...

But changing the rotation parameters would in turn make the ballscrews drive the opposite direction of what they are right now. From the perspective of the control when you tell it to go positive...

If you're still set on changing the 0,0 point, you should be able to just change your motor rotation parameters and change your home position (along with the necessary Limit switches).

I didn't...

And if you would've read my post you would see that I indicated that I have not tapped on a 15M, and that I wasn't sure if the parameter sets were close to a 16M as I've never had any reason to dive...

G95 is setting it up for feed per revolution. I've never tapped on a 15M, but if the parameter sets are comparable to a 16M there is a parameter specifying whether or not a rigid tap M code is...

This is a signal internal to the controller that can be used by the PMC. If you're wanting to put a cycle light on the machine you would have to edit the ladder using this signal and tie it into a...

My example is wrong. That would essentially turn the stack light on for about a milisecond, and then shut it off for the timer's preset. The correct way would be
...

Sub3 timers are set in the PMCPRM page under TMR. Sub24 timers are "fixed" timers in the sense that you have to physically edit the ladder to change the timers preset.

If you're trying to get a...

Mitsui, he's not starting over from the beginning, he's starting the program in the middle. Since his work coordinate is called at the beginning of the program it doesn't get reinstated when he...

On the 180i you can, but you have to run the HMI software rather than the standard Fanuc screen. I don't believe there's any other way to do it.

The easiest way to find out would be putting the machine in MDI and keying in #1=#0; and cycle start. If the control takes it without alarming out, Macro B is enabled.

From there when you pick up...

Your axis is rotating correctly. Direction is determined looking through the back of the motor.

Looking at the end of the motor when you press the + button the motor turns clockwise from this...

I have a customer that uses old drills(carbide) that have been reground to the point he can no longer use them. When the part is not seated correctly the swing clamp is at a different height than...

Power off the control(just control not the whole machine).

Press the far right arrow key and the key immediately to it's left and continue to hold as you power on the control.(Buttons directly...

That's correct, but some of them are control specific. For example, you can block out the ladder edit function on some of the controls by a keeprelay.

What control are you working with? Any...

It needs to be pretty close. Take your alignment tool and keep bumping the bar feeder around around until you can get full 360 contact without pushing the string up/down or left/right.

One thing...

I've been putting IFM Efector capacitive sensors on my belt driven spindles for a while. They are non-metallic proximity sensors and have a teach function that allows you to program the distance to...

You can pass parameter data to the cnc but it's tricky to make it work. You would have to add several Window read functions into the pmc, then make outputs as to the status of the parameter, and...

OT 113 CPU ERROR:
The CPU or a peripheral circuit of the speed control unit of the
spindle motor is faulty.

What are you trying to do?

You're right about setting your 6080 to 119 for the macro. I sent you a PM with my email address. If you can, make a backup of the machine ladders you would like to be able to do this on and email...

dug it up, but I had forgotten that I had to make some ladder edits to make it work. Explanation is below. If you're interested I could walk you through doing the edits required to make it work,...

It's on my work laptop. I've got one more customer to drop by, and will post when I get back to the house.