Hi,
if your battery was problem, i think your bios settings restarted. For Ultimax settings for hard disk has to be specificed, like cylinders head and setor numbers ( usually is 3303 16 50 ) so...
Type: Posts; User: hurco_man
Hi,
if your battery was problem, i think your bios settings restarted. For Ultimax settings for hard disk has to be specificed, like cylinders head and setor numbers ( usually is 3303 16 50 ) so...
Usually something like this could be 5V power or limit switch cabel.. Does it give fault in similar situation or random?
I need help! Does anybody have runnIing Ultimax3 board with Phoenix 80386 ROM BIOS PLUS ver. 1.10.18 or similar??
I need setup, there are maybe 5 or 6 items to be set up in BIOS.
Hey, that is also way to go. But im think that price is around 3000€ for kit, or around 4200$.. And there is also labor hours. But again, cheaper and better then DSP technology..
Here, if you dont belive me here is photo of board which i have on my stock. Its Hurco code which i have told you, only newest version.
Yes, but i told you what is that number. You can look on PLWd
And you are sure that problem is in that board? The serial number of that is 415 0247 009 DSP Motion Matrix4n Board - price, 5 800,00€ - new, from Hurco :-) I think you can get it online...
Can you make photo from above, front and back side?!
One of possibilty is power jack on DCIO backplane board. There are usually also know to be problem. If you move DCIO boards, you can see plug on the top of DCIO backplane board, try to take it out...
Setup of axis travel is ok. Can you tell me can you move axis from limit switches? From X and Y + status?? Can be you have problems with limit switch cabels...
Ok, that could be also servo mismatch or you need axis balance. But if you are sure its problem in DSP board, i need photo of board to indetify.
Yes, i can help you but i need some info or photo to recognize DSP board - there are many models and years of produce.
also, first try to reset all contactors ( ATC CW, ATC CCW, ABS, SCC ). Try to push and release black buttons on them ( but first check that tool pocket is not down and no tool in spindle ).
Uff that depends. Is it exchange arm in 0°? Tool pocket up? If they are, then the senzors are not working or some electric safety is tripped...
You have access to a lot of information :-) Yes, i also mean to tell him that but thanks ( in his name ) for advice.
Off course, i am sorry. He told me that everything is ok when he is driving axis except when machine is going with Z axis in tool change height. I ask him for software version and servo pack type. Do...
jel možete poslati sliku upravljačke jedinice ( konzole ) te možda sliku početnog ekrana nakon dizanja sistema ( pretpostavljam Ultimaxa ).
Ne mora da bude, moguće je da je samo parametar brzog posmaka ( koristi se kod dizanja z osi ) krivo podešen. Koji je softver instaliran??
Can you write what is the problem? I mozete da napisete na srpskom, ima nas ovdje.
If your Hurco is prepaired for 4th and 5th axis, then you should have DSP board prepaired and no extra costs. Naturally, its never plug and play and every time, every machine, is different. Did you...
Can you give any information about hardware on your Hurco and which 4th axis do you wanna put up??
Maybe i am too late, but question. When you swap X and Y servo drives did you swap and power cables to it or just data cabels? If you left power source same, doesnt have to be servo drive.
Yes, we say "Its always fun with Hurco". Usually that kind of error knows to be 5V power or cabel of limit switches, but in your case you know its a DSP board. So you searching for the new board? If...
i can ask someone about that because i´m not sure for that boards, could be you need both of them if is old machine.
Usually difference is one board is for 3 axis machine and second board is for 4 and 5 axis. What kind of machine do you have and do you have extra a or/and c axis?
What is Hurco serial of the board? In the format xxx-xxxx-xxx rev x??
hello,
i have problem with Hurco BMC4020 with Ultimax2 cage and Ultimax 3 multibus board ( CPU ). The problem is that BIOS settings are not remembered after exit form BIOS. Software installed is...
Hello,
To repair that kind of boards is very difficult because there are no schematics but i think you can fit this boards, and in my opinion they are not too expensive.
Hurco Ultimax Dual...
Which software you have on the machine? i can send you hurco documentation about setting up ultinet option
i have spare one, original Hurco, not used so you can send me mail if you are interested