Search:

Hello I have just downloaded the trial and I really like it with my new rotary!

Before what I would do is make two halves of a corbel and then glue the flat side back to back the carved portion...

Thats the link I pasted, I went ahead and ordered this and it went bad within a couple of weeks. After lots of feed dragging they sent me another which did the same thing. I Finally purchased one...

Amazon lists some as being DC -AC and AC -AC I am guessing the second one is correct?

I started off buying cheap generic end mills off ebay but now I know better, the amana 46249 is the best for roughing I have found, it makes confetti size chips and loves speed, the other one I use...

I would go with an UGRA spindle I have had nothing but trouble with the ebay china spindles, it is worth the extra cost believe me.

247186

Hello I am attempting to setup a relay to control my dust vac and am having problems that make no sense to me. My older machine has a cnc4pc relay board I setup so I purchased one for the...

Thanks! I have purchased a mini rockler clamp and had pretty good luck with it, Soon I hope to get the larger ones and try them.

I am thinking about purchasing a new spindle the one listed here (CNC Spindle for CNC Router 2 2KW | eBay says it has NSK bearings and is about 100$ more than its competitor, This would be a good...

Hello I am looking for some t slot clamps for a woodworking cnc machine the oem ones are made out of really soft metal so they don't work very well.
Here is what I have
...

Anybody out there??? also can somebody recommend some better hold down clamps that will fit this machine??

I am still using this machine and still happy with it. If you have any questions I will...

Hello I though I would post some pictures of my kl-1212, this shows some of the detail I was not able to find elsewhere. I bought it off Craigslist to replace a rack and pinion machine that I had...

-update- I have replaced all the bearings, pinions, mdf table,spindle nut, collet and a lot of other stuff but am still getting lines. Could the rack be bad? I have had this machine close to 3 years...

I put the old pinions back on for troubleshooting, the third picture shows the new gears I think. The newer gears have bearings instead of bushing's and roll easier.

That's exactly what it looks like. I been using two new bits both good quality 1/8 tapered ball nose and 1/4 ball nose but still no luck . What I have done to check tension was to reassemble the...

I dissembled my gantry again and checked everything for proper tension and slid it back and forth to make sure it rolled well, bearings are in good shape. I don't think that this could be a...

I am still having problems with this if anyone else has any ideas, Its been broke for about a month now. I have disassembled my gantry and make sure everything rolls evenly, replaced the dumpster nut...

Just an update I believe I found my problem one of the pulleys on my x axis had a set screw that was just loose enough to give it some slop but not enough to let it move when pushing on the gantry.

I have tramed it, it was needing it but did not help my problem.

206752

I have tried in different pieces of oak and cedar they all do the same :( I have not had great luck climb cutting, rastering at 90 (Y axis )does work fine, but I like to cut with the grain...

Hello I am having an unusual problem with my rack and pinion router table. When I am raster cutting anything it leaves these lines on the material opposite of the axis I am cutting
The top pocket...

A large part of the problem was my usb wireless adapter. I'll keep the old machine for a backup, but everything seems to be running good now. THANKS CNCZONE!

Thanks a lot:cool: turns out it was my usb wireless card, I also tried other things like clicking on the windows key or bringing up internet explorere and it would cause the same halting problem

It is a single core ftp://ftp.dell.com/Manuals/all-products/esuprt_desktop/esuprt_dimension_desktops/dimension-8250_user%27s%20guide_en-us.pdf

Yes I went into diagnostics menu and toggled the toolpath. And the screen turned into a grey box, I had though it was only doing it on the large file, but after testing it with a smaller one in does...

Hmm tried turning the screen off, it did run smoother but it still has this problem. Then I tried a similar but much smaller file and it does the same thing. This is happening to both steppers on my...

I am having some trouble with my machine when I load a large file (30 meg) or more, table would jerk occasionally and some times I get a driver warning when I load the file The driver test results...

Hitachi x 200 http://www.clrwtr.com/PDF/Hitachi/Hitachi-WJ200-User-Manual.pdf
On page 39 it has an alarm signal maybe I could use that?

Sure i'm using a 2.2 kw spindle with Hitachi vfd which is set to use as an external on off switch that goes through the relay on my board, its not the right way but I am not smart enough to wire it...

Thanks a lot for the info I really appreciate it! The simplest thing to do would be to get a ups with relay, but all the ones I have found are 200+ bucks just for the interface card. Am I correct ...

Feed hold sounds like a better idea, Can you recommend a relay that I could use for this purpose and what the name of the signal would be on ports and pins?