Search:

Please help identify this power connector and where to get one.

Thank you and Merry Christmas.

I am new to vacuum forming technology. I am planning to make around 50 of 20" x 20" x 3.5" square bucket. The bottom of the bucket I like to have some pattern like square or diamond dots like the...

For example my gear is 5 inch diameter and the weight of the load is 200 lb what is the minimum torque I need to lift the weight. I assume the height is constant so it doesn't you lift 1 inch or 1...

Thanks everyone for sharing with me all the great information.

If you don't mind can you please draw some sketches for me to visually better. I don't get the concept and I try to draw it on the paper is all moving the wrong direction.

Thank you.

My input would be around 1800/18. So is a 100:1 ratio gearbox and yes you are correct gearbox need to prevent the conveyor from back driving the motor.

Thanks

You are right I need "Contra-Rotating" Shaft gearbox. I have google nothing coming up for that except airplane propellers. Do you know where can I find that or may is cheaper to have to 2 gearboxes...

If is the shaft is one piece than it would work. Is there a gearbox that I can use. I have any picture probably is easier to understand. I am building a rack conveyor so instead of two gearboxes I...

Yes that what I am looking for when you look at the gearbox one end is turn CW and other end CCW like the picture I have here. If that is the case that the right one for my need. My drawing is lousy...

I am looking for a dual shaft gearbox that can output turn CW and CCW. I have never use a dual shaft gearbox before. So is there a dual output gearbox.

Thanks

Currently I have two AC Drives that I use for this project the Drives are from TECO model MA7200 and 7300CV. The 7300CV has PLC functions built. This is description for the drive. I think it should...

thank you

No, I don't have any experience with programming microcontroller.

Thanks

I know how to calculate 2 pulleys ratio but when 3 pulleys I have a little problem.

For example driver pulley is 10" diameter driven 30" pulley the ratio would be

3/1 or 3:1

How are about...

I have this bridge saw with no controller. I have spare servo drives, motors and some stepper motors and drives.

Also I have AC Drives with gearbox motor. The AC Drive is Teco MA7200 with lot of...

I have wiring schematic and have hard time interpet how to translate into simple wiring for E-Stop and Safety Door Guard.

My equipment will not without the two safety switches in place.

...

Sorry, I wasn't clear about the is an AC Inverter, not AC Drive. I don't know that make any difference. It is not servo motor but a 3 phases motor.

Thanks

I am building conveyor belts will be using one AC drive to control 4 motors. I like to install switch between each motor after the AC drive, so each motor is independent control. I know all the speed...

Bob, you are right on stepper motor when is powered there is torque but I check the Demand Products that the Large CNC is control by servo motor. I was thinking that servo motor has no torque during...

Can you share with me how the setup the air cylinder to control tension. May be a few photos. How is the tension control by the volume and pressure of the air?

Thanks

Can you use timing for vertical or Z-axis, will the weight of that axis push it down. Since belt has no holding torque, I was thinking is have to be screw.

Thanks Matt!!

I have Mitsubishi Servo Drive with specification: For 3-phases 200 to 230VAC, 3-phases 170 to 253VAC

It didn't say any type of phases, in my warehouse we have 240/120 VAC Delta, since Delta has...

I am looking for spindle type, because the Porter Cable will not meet our duty of work.

Thanks

I have read everything posts about automatic tools changer in this forum and many other sites. But cannot find a place where you can buy a reasonable price ATC for CNC router. Can you get an ATC...

Few weeks ago I saw one of the CNC router has this kind of Y axis drive system. I am planning to make similar design. Where can you buy that bearing block. What is the name of that block may be I...

I like to know too any update?

That is very good idea but will the hot wire burn the acrylic piece?

Hi Dan,
How do you attach the wire to the machine and how you insulate the hot wire from it. It sound a little scary for me.

I need to find a solution or build one for around 80 feet of wire....

The final thickness is not that critical.

Thanks