Search:

No problem, any other issues just let me know, you have my e-mail.

Good luck.:cheers:

No problem to fix.

LineCode # Linear move
G1 Z[D] F[FRate] # Z[D] by itself (no G99, or X, or Y)

Sent updated postform.m.

Easy fix, just move the G99 to where you need it. I assumed "after" was on another line and not directly after. I sent you an updated post.

It means your air pressure to the machine has dropped below 80 psi. Put a inline regulator on the air line that goes to your machine and set it a 90 psi.

Also, you might want to check your...

Try leaving .005 for a finish pass or a spring pass at a slightly faster feedrate.

Show us some program code where the crash happens, then it will be easier to help you.

Sequence#s N 0 5 5 # Char, freq, incr & start (CHANGE LINE TO THIS)

N[Block] (REMOVE ALL INSTANCES)

LineCode # Linear move
G1 X[H] Y[V] Z[D] F[FRate]
G99...

Can you show the post you are trying to edit? Sounds like you have something else going on. Might be able to help you fix the other stuff you want alot easier.

Do you have any N[Block] commands in...

I usually open the file in my editor and use the "remove blanks line" feature and resave it. PIA, but it works.

Try "Sequence#s N 0 5 5".

You can try this:

# Output a safe startup of CDC :
Infeed
G<Side> D<DComp> X<H> Y<V> F<FRate>
G99
end

There are people on here that can help, just tell us what the issues are.

Just remember to make a copy of your existing post before you make any changes, that way if something happens you still have a working post and dont make to many changes at once. Also you can...

Just got tired of waiting for my resellar to "fix" my post and started asking questions, eventually you try things on your own and figure things out.

Not sure if this will help, but one way to get the date is to find the "SBackDoor Supressheader" line in your post and space it over, this will fill in your Company name, address and date. I did a...

Here is a mixed bag for ya. I run format 2.

%
O1(P/N OP)
G90 G80 G70 G40 G17 G0
(2.5" MITS )
(MILL 1.00 DIM )
M6 T1
S2292 M3
G0 G90 X1.55 Y-1.125 E1

http://www.practicalmachinist.com/vb/showthread.php?t=176196&highlight=surfcam+sale

See this thread....hope this helps.

I use:

G0 X0. Y8. E0
M30

This will send it to machine X0 Y8.

You have a g80 right before you canned cycle callout. Try removing that, also you might want to add your XY on your g82 line.

T1M6(CENTER DRILL
G0 G17 G40 G80 G90
X.875Y.625E1S1200M3
Z1.D1H1M8...

You can go on Surfware website and see some of their case studys and kinda determine what you want to run. Rule of thumb from what I been told is double your SFM, triple your IPT. Also depending on...

Just loaded Vel. 4 SP 1 and when you import a Solidworks sldprt or Parasolid you can also import the sketch geo. on a different layer and color. No mods. needed comes in clean and the radius are not...

What is the process for that and how do you save it? When I tried it, the model came thru as whole not sectioned.

A+ on that, that comes in handy when you want to do a dummy toolchange.

I also use If/Endif on my lathe post. Say I'm using T1 to face/turn, I will program the face as T1 and the turn as T101 and...

Go to the "Help" drop down menu and you will see "multimedia tutorials". These are pretty helpful and should get you started. I've been using Surfcam for 14yrs and have been playing around with...

What are your prices for a Fadal 40 taper that doesn't have TCS already? Your website doesn't display the cost only says to call!!

Break your depths into increments. Go .03 deep or so, retract out of part so the chips can be flushed out. Repeat until you get to the desired depth.

Looks like you have 2 different styles of "spokes". I would program it down to selected levels depending on depth of cuts you wish to take. This would involve a little time to get the geo. for the...

I've done that did it, you still need to redraw your radius's and some lines. Draw something up in SW with radius and chamfers, bring it in to SC using create > spline > cross section and analyze all...

I always do my SW files in the FRONT plane, when you import them into SC they will be in to TOP veiw.

I am running SW '09 SP 3 and can open in Vel. 3 & 4 with no issues.

When I create a revolved base/boss(like a shaft or wheel) in Solidworks and I import into Surfcam and create > spline > cross section to get my geometry for lathe tool paths, why do I have to redraw...

Hey Bala,

Change your G81 in your post to:

G81 G[RetPlane] X[H] Y[V] R[Vclear] z[D] F[FRate]

if that doesnt do it, you'll have to show me your post so I can see how it is setup.