584,805 active members*
4,854 visitors online*
Register for free
Login

Search:

Type: Posts; User: MCPservice

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: Multicam: System enterrupt: port 109=0x 10 z home

    Were you cutting metal?
  2. Re: Newbie - Used MG305-03445 Pendant Hangs on Validate File

    So the system locks up when you choses the existing test files in PSS?????
  3. Re: help needed please - Multicam 3000 Series Model 2013

    Blink count 5 is normally a mechanical issue either your servo motor or possibly your bearing cars. I would with the machine off try to push the Y axis and see if you are able to move it with...
  4. Replies
    2
    Views
    219

    Re: Multicam Apex 3R loose connection

    Did you set a static IP address for the PC you are using to communicate to the machine.
  5. Re: Teknic ADT-E card needed to program Teknic Eclipse Motor Drives in Multicam 3000

    If you still have the old drive and it can power up you can if the machine uses a 2521 or never control board, use the control board to save the old parameters and upload to the new amplifier
  6. Replies
    0
    Views
    172

    Re: Multicam 3000 from 2013

    open up th control cabinet and post a pic.
  7. Re: Multicam 3000 - Drive is working in reverse

    You have to program the drive to the correct axis, you might be able to call Multicam for the drive parameters.

    You will need the teknics communication software and cable to talk to the drives or...
  8. Re: Multicam 3000 remote stuck on the welcome screen

    Check to see if the control board is booting up completely in motion mechanic, if you can see the system fully booting up then the issue is the keypad
  9. Replies
    9
    Views
    4,538

    Re: Need assistance.

    which axis?????
  10. Replies
    1
    Views
    778

    Re: Vacum Grid Material Replacement

    https://www.interstateplastics.com/phenolic-plastic-sheet?kw=phenolic%20sheet&gad=1&gclid=CjwKCAjwt52mBhB5EiwA05YKo19KfYsEx-Zs-Kwc6kkbkLbUAnQCBa_zjGlbWBntheGTbpAfuqRpbRoCKuIQAvD_BwE

    you will need...
  11. Re: multicam 3000 - running cnc without controller

    You might be able to change parameter 60 to 2 but you might still run into the issue of not having the correct inits and firmware to run the system without the keypad.....
  12. Re: Multicam 3000 2005 machine Teknic SST-1500-561

    Multicam told you kind of half the story, Teknics is phasing out those drives but they have not yet. They will keeping building drives until all the parts required to build those drives run out.
    ...
  13. Replies
    1
    Views
    1,021

    Re: System interrup multicam 3000

    What is the fault on the inverter?
  14. Re: Multicam V Series Cannot find Hard Home!!!???

    John this is a time where you should have someone come in and properly set up and train you on the machine.

    I'm pretty sure with a 2020 machine you did not get it for a song and a dance....
    ...
  15. Replies
    2
    Views
    1,745

    Re: Multicam 3000 Modbus 1/20

    With the machine off....Check your Rio board connection ( Unplug and replug all of the connections on the Rio and that the Rio board is not covered in a nice warm blanket of dust....Electronics don t...
  16. Replies
    3
    Views
    1,754

    Re: MultiCam PPS Software

    MultiCam Southeast | CNC Digital Finishing, CNC Plasma, CNC Laser, CNC Waterjet, CNC Router Bits
  17. Re: Multicam technician in Las Vegas, NV area?

    Give me a call I may be able to help you out....

    678-548-1483
    MCP Services
    Maurice Phelps
  18. Re: Faulty Z Axis teknic Eclipse Servo Drive For Digital Express

    If the drive is faulty the error will stay on the drive.

    If the issue is cable or servo motor then the error will move from servo drive to servo drive
  19. Re: Faulty Z Axis teknic Eclipse Servo Drive For Digital Express

    If the drive is faulty the error will stay on the drive.

    If the issue is cable or servo motor then the error will move from servo drive to servo drive
  20. Replies
    2
    Views
    844

    Re: SYSTEM INTERRUPT: SERVO FAULT

    Main spindle motor bear was damaged? Or the servo motor bearing was damaged?
  21. Replies
    5
    Views
    1,233

    Re: Need Help with MG205 Communicating

    IS this a multicam plasma or a ez cut plasma??//
  22. Replies
    6
    Views
    1,551

    Re: Backlash compensation parameter?

    There isn't any compensation for backlash because you can only turn out so much, eventually there is no number you could put in the controller to comp out.

    On a Multicam machine you more then...
  23. Replies
    7
    Views
    2,496

    Re: Where to Buy a CNC Router Machine?

    As a tech that has experienced various machines from multiple countries...my experience with Chinese machine have been challenging with the lack of documentation, 12 hour time differences to speak to...
  24. Replies
    1
    Views
    530

    Re: MultiCAM-MT510

    Lifting Cable....you might want to upload some picture on the site here to give better idea of what you are talking about
  25. Re: Multicam & Enroute 6 software for installation are needed

    You should be able to call Scanvec, if you have the Key Number they will send a link to download Enroute 6. As for the Multicam software how old is the 1000 series and what OS will you be using with...
  26. Replies
    2
    Views
    838

    Re: need help multicam 1000 K-axis

    Does K axis actually find home?
  27. Replies
    8
    Views
    2,411

    Re: M3000 starting job then nothing

    And you are using a static IP?
  28. Replies
    8
    Views
    2,411

    Re: M3000 starting job then nothing

    How are you connected to the router...

    PC to machine

    or

    PC to switch to machine...

    Ethernet comms
  29. Replies
    8
    Views
    2,411

    Re: M3000 starting job then nothing

    How are you connected to the router...

    PC to machine

    or

    PC to switch to machine...

    Ethernet comms
  30. Replies
    8
    Views
    2,411

    Re: M3000 starting job then nothing

    Are you using Job Server as the program to communicate with the router?
Results 1 to 30 of 447
Page 1 of 15 1 2 3 4