Please follow the links given below for information:
http://www.machinetoolhelp.com/
http://www.cncci.com/
Type: Posts; User: smabhyan
Please follow the links given below for information:
http://www.machinetoolhelp.com/
http://www.cncci.com/
Dear Sanate,
I have not worked on Matsuura, but a Milling spindle does not vary much from machine to machine. Following are my points:
1. Why does the Clamping System Need Overhaul?
2....
Dear Radish,
Which axis looses position?
Is it Gravity axis or any other axis?
How much is the movement?
Kindly clarify.
Someone suggested me in CNCZone about minicomm. This is the software, part of Linux system.
At Command Prompt type minicomm.
The software will start working.
The Idea given by Eurisko is quite practical for DIY man.
Some changes or fine tuning the circuit to suit your requirement are needed.
Compressor applications demand current continuosly, which...
Dear Sir,
Following are the links for the High Precision Ball Screws.
They will not be cheap.
My suggestion is to take a ballscrew of 0.002 to 0.003mm precision & do Pitch Error Calibration of...
Please log on to www.heidenhain.com & from softwares menu. download TNCRemoNT software.
It will work properly with your control.
Sanjay
Dear John,
I have a pdf file about formulae for machining power calculations for various materials & processes.
If you send me your e-mail ID, I will send them to you.
Sanjay
Dear Brenck,
Go for backlash free direct coupling. No reversal errors, no position losses due to transmission errors between pulley & belts.
You can find variety of couplings on www.ktr.com
Dear Walt, Hu
What you are all explaining works well.
Here the point is for precise measurment of Tool Length & Dia., a Tool Pre-setter is required (when the shop has multiple machines).
...
The Tool Length Offset is always measured from the Face of the spindle to the Tip of the Tool. This Length Offset is always constant irrespective of the Part height. Tool Length is also positive...
Dear Parminder,
For Fanuc O-serie controls, the TAPE or Drip-Feed mode can be normally selected through Mode Selector switch. Does your machine has this mode on the selector switch or not?
If...
Dear Parminder,
Why you want to run a small program through DNC.
If it small, transfer it directly to the control & run it with M98 Pxxxx Lyy.
xxxx is the four digit program number (without the...
Please send me your e-mail ID.
I will e-mail the procedure to you.
Hopefully it will work.
Dear Dave,
Thank You Very Much for the help.
I will check up both the alternatives given by you.
Dear Lerman,
Lot of Thanks for the reply.
I will check the details on my PC.
Dear Lerman, please make your point more clear. I do not understand it.
I like to connect RH Linux 9.0 PC to CNC Machine to transfer NC programs.
Does anybody have (or know whereabouts of) a Serial Communication software for RH Linux 9.0 PCs?
Dear Intel Praji,
Contact SKF service center at following numbers, they may help you.
SKF spindle Service Center
Pune
Phone: 0212 4112477 / +919372416041
Moving Gantry design is used for machines with large X-axis stroke. Normally the X-axis stroke should be beyond 10 meters or more.
It also implies that the workpieces are large and heavy.
In case...
The mechanical construction of the machine matters a lot.
Also matters is they way the machine builder is tuning the control to the mechanics of the machine.
Some companies tune Fanuc control in a...
Dear Noah,
Are you Trying to Machine a Ball Screw or Lead Screw?
How will you make the Ball Nut? What about Tolerence to be maintained bewteen Nut and Screw to fit Balls?
1. You have tools assembled and ready near the machine.
2. You have Tool Length and Radial Offset already measured and available on a paper.
In such case, you can take 5 minutes per Tool as...
Dear fjd,
You need to run Universal Drilling Cycle. It works exactly the way you want. The Cycle Type is Cycle 203 in TNC 310 Control.
I can send you the relevant information regarding this...
Looks Like Problem with COM Port.
Please swap it. Com1 to Com2 or Com2 to Com1.
smabhyan
Dear Murray,
No need to worry about the RF noise from the Servo-Amps. You can mount them in same cabinet.
The care you need to take are as follows:
All the Cables carrying precision Signals...
Looking for Operating and Electrical Manual for Mori SL-3 with Fanuc 6-T Control.
Can anybody help?
==============================================
smabhyan
[email protected]
Looking for Operating and Electrical Manual for Mori SL-3 with Fanuc 6-T Control.
Can anybody help?
==============================================
smabhyan
[email protected]
The Information I am looking for is available in Following Fanuc Manual:
Fanuc FA System for PC / Windows NT Version / Operator's Manual
Manual No.: B-75044EN.
In case somebody has this manual,...
Dear Mouldmaker,
I can only communicate from PC. I have no screens on the control to access remote PC.
I can use softwares like CuteFTP, however, first the PC side configuration need to be done.