584,858 active members*
4,632 visitors online*
Register for free
Login

Search:

Type: Posts; User: danielwilcox

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    471

    random orbital spindle?

    I'm building a machine to automate a sanding process on a tile line. Right now, i'm rigging up a random orbital sander/polisher with an 8" backing pad on a frame with an adjustable height over a...
  2. Replies
    1
    Views
    1,567

    CNC Machinist needed in Oceanside, CA

    We are looking for a machinist to program and run our 3 axis CNC router to manufacture molds. Most of the material is wood, foam, or composites/plastics. Our molds include 2 axis flat work and 3 axis...
  3. Replies
    21
    Views
    12,226

    Re: HSD ES919 Spindle bearing removal help..

    which thread was right hand? i got the smaller nut off that retains the upper two bearings, and that was left handed. was yours right handed, or are you talking about the lower larger nut that...
  4. Replies
    0
    Views
    1,300

    Post Processor for Dynapath Delta 10

    Hi guys,
    I'm looking for a post processor for my Lagunmatic vmc 3516 mill. We use Router-cim for our cnc router, so it would be nice to get a post for that, but a post for any open sourced or free...
  5. Replies
    7
    Views
    3,378

    Re: Takisawa MAC V4 toolchanger issues

    after a long battle with getting this machine going, i encountered an issue. i can only do a toolchange if i home out the machine's z axis before every toolchange. g28 and g30 will bring it to the...
  6. fanuc 6m, relative position is always 0?

    I just got our takisawa mac v4 4 axis mill running. I havent touched an old fanuc controller in probably 10 years, so i'm a bit rusty. I am trying to set my tool length offsets and work offsets, but...
  7. Replies
    2
    Views
    1,030

    arrow 500 electrical hookup issues

    We have a Cincinnati arrow 500 with a vickers 2100 control. We have just moved this machine to another building, and hooked it back up. It worked before, however now it will not turn on. We can power...
  8. fanuc 6m external message 2097 MG-T ?POS

    Hi, I have a Takisawa MAC V4 4 axis cnc mill that i've been slowly getting going. It has a fanuc 6m control and is displaying external message 2097 MG-T ?POS when i try to run a program. Anyone have...
  9. Re: Yang YAM CNC CK-2 lathe with Fanuc 6-T control.... stuck in bubble read screen

    Anyone?
  10. Replies
    7
    Views
    3,378

    Re: Takisawa MAC V4 toolchanger issues

    got it all rebuilt and it works great now.
  11. Replies
    7
    Views
    3,378

    Re: Takisawa MAC V4 toolchanger issues

    so i started taking the toolchanger apart. i believe that it was hydrolocked, so i am in the process of rebuilding all the cylinders. this would explain why it wouldn't go back into the home position...
  12. Replies
    7
    Views
    3,378

    Re: Takisawa MAC V4 toolchanger issues

    thanks. i guess i'm used to my old (newer) mills where you didnt have to enter that.
    i got it to start a tool change but it stopped in the middle of it. I suspect the pneumatics are sticky or...
  13. Replies
    7
    Views
    3,378

    Re: Takisawa MAC V4 toolchanger issues

    I restarted the machine and now i am able to rotate the magazine. I still can't get the arm to rotate or move up or down though.
    Also, when trying a toolchange in MDI, i get an alarm 2098 Z-ZRN?M06
  14. Replies
    7
    Views
    3,378

    Takisawa MAC V4 toolchanger issues

    We just got a Takisawa MAC V4 cnc mill with a fanuc 6m control. We did some work to it and got the spindle and axes moving, but the toolchanger is not functioning. We cannot rotate the carousel, or...
  15. Re: Fanuc 6M controlled mill, spindle drive alarm 02

    fixed it, the RV18 pot had to be adjusted.
  16. Re: Takisawa MAC V4 with Fanuc 6M controller issues... motors dont move, position sho

    fixed, we had to adjust a pot on the servo drive to get the feedback to work.
  17. Re: Fanuc 6M controlled mill, spindle drive alarm 02

    We probed the sensor again and it seems to put out a decent sine wave now. not sure what i was doing wrong.
    However, the spindle now seems to have a noise when it's on, it has sort of a click/thud...
  18. Fanuc 6M controlled mill, spindle drive alarm 02

    I have a Takisawa MAC V4 mill with a spindle issue. If i turn the spindle on, it spins for a second then faults and the 02 alarm LED turns on, which appears to mean that the commanded speed does not...
  19. Re: Takisawa MAC V4 with Fanuc 6M controller issues... motors dont move, position sho

    that makes total sense, i was messing around with it the day before. I will try it. THANKS!

    new issue arose.... i tried turning on the spindle with mdi. it turns on then stops immediately and the...
  20. Re: Takisawa MAC V4 with Fanuc 6M controller issues... motors dont move, position sho

    ok we figured out that it was actually moving, just very slowly, and for some reason it was on a different position screen that just showed zero.

    HOWEVER, the z axis is still not moving. We can't...
  21. Yang YAM CNC CK-2 lathe with Fanuc 6-T control.... stuck in bubble read screen

    We got a Yang CNC CK-2 cnc lathe with a Fanuc 6T control the other day. I've been trying to get it powered up, but it just reads BUBBLE READ on the screen. It appears that the old bubble memory card...
  22. Takisawa MAC V4 with Fanuc 6M controller issues... motors dont move, position shows 0

    We just got a 4 axis Takisawa MAC V4 with a Fanuc 6m controller. We had it powered up and moving the other day, but today it is having issues. First, all axes except for Z moved and homed out...
Results 1 to 22 of 22