I am starting to bring up a broken TV-30, and the first thing I notice is Program, Available Space 0, Available Files 0 (NC Program List side)
I am unable to load 200-All 2, 2-Tools, 5-Common.
...
Type: Posts; User: chrisclub
I am starting to bring up a broken TV-30, and the first thing I notice is Program, Available Space 0, Available Files 0 (NC Program List side)
I am unable to load 200-All 2, 2-Tools, 5-Common.
...
Hi,
I can help change Japanese to English...
go to GOP, turn off the keys, push down arrow until 20 is displayed, change it to a 1, then power cycle the front panel.
Hi Moghal,
Piece of cake.
My email is [email protected]
X zero is far left, Y zero is far front.
You can maximize your X and Y travel if you put it there manually with the power off...
Glad it helped. Please send me an email to [email protected]
Thanks,
Chris
Hi Shay,
Yes, resetting GOP parameters can solve a lot of problems...
1. Turn off the GOP write protect keys
2. Page down and change 39 to 123
3. Change 38 to 98
4. Change 21 to 1 (to go...
Doh!
E-STOP was in because I had pressed it. LOL
I have an EMG EMERGENCY PLC alarm
and a M01 operation error 0101 and the spindle wont go up or down.
Any idea on how to release these alarms?
the Y1C2 (1) (2) trick doesn't work...
Thanks,
Thanks Jim. I was able to load the NC programs and edit them fine using POS/SEARCH
About the Z adjust...
Should the chamfer on the top of the pull stud on the tool holder contact the chamfer...
On to programming...
I have a couple questions...
1. In the POS/SEARCH, it comes up "TAPE (0)", I guess TAPE (0) means search Memory, and TAPE (1) means search a tape?
2. Even though the...
Thanks to Custom and Harri's old posts, and a lot of help from Custom these last two days, I got all the axis zeroed and no more alarms!
But I am afraid I will still be bugging you for help till I...
Hi again Custom and nice to hear from you Harri!... it was your old troubleshooting posts from 2009 that got me here. Any help you can give me is much appreciated... I hope you still accept virtual...
Custom, That was great help last night!
I have one other problem, maybe someone knows while I am zeroing my axis...
2. The NC Programs menu only has "O-NO Alter, DEL, COPY" functions. No...
The ABS SYS line reads: (X) ESS (Y) ESS (Z) INC (C) INC
The TYPE line on the next page reads: (X) NO STOPPER (Y) NO STOPPER (Z) INC. (C) INC.
The STATE line on the next page reads: (X) NG (Y)...
Thanks again!
I got the fax, however, I have to clear the "Z70 abs. Illegal" alarm before I can go farther. Currently I can not move Z down (it only goes up now).
My TV-30 just has a simple X-Y table, no pallet, etc.
Please fax the GOP parameters and any thing else that might be helpful to fix the "Z70 abs. Illegal" alarm and convert the machine to inch.
...
Thanks a lot for your help.
I found a blue rectangular device about 1"x1"x2" made in Germany with a roller on the end that retracts about .25" when pressed, however, it does not contact the wall...
Thanks for your help, Custom B.
How do you find the Z limit switch? I do not have a maintenance manual for this TV-30.
And no, I have not done a Z zero adjust before. I assume I just move the...
Thanks!
I think I change 1040, 1041, 1042 from 0 to 1, any others? for metric to inch.
I'll check the sticky switch tomorrow.
The Z only went up, and severely overtraveled when I tried a zero...
I have these two problems with my TV-30:
Z70 abs. illegal error
Z will only move up
I am also trying to change the machine from metric to inch.
Any ideas?
I found one link...
Mitsubishi Electric Automation Inc. - Search Results
Thanks for your reply. What I really need is a PDF of the parameters. Maybe someone has a link?
Which parameter do you set to run in inch mode?
This has MSC-802 control.
Thanks!