Any further progress with this. I am having the same issue with the same machine.
Type: Posts; User: docdesigns
Any further progress with this. I am having the same issue with the same machine.
Hi All,
* I have 1998 Hitachi Seiki TS15 with seicos sigma 21 control.* I recently had the timing belt in the turret start to fray and the belting was pulled from within the middle of the belt...
Just to answer my own question for any one else looking in the future. The parts conveyor starts when the part catcher down/retract M code is given.
Hi all,
I was recently trying to install a LNS Quick load bar feeder on Hitachi seiki TS15 lathe with seicos control. I have a few different diagrams that show the wiring a slightly different...
Thanks John,
I do have the manual with parameters in it. I just don't know where to look to turn the option on if that is even possible.
Clinton
Hi,
The lathe in question is a 1998 Hitachi Seiki TS15 with seicos 21 control. I am having issues with canned cycles. This is a new machine to me. The programs left in the controller do not use any...
Hi All,
I have a Hitachi Seiki TS15 that I am gradually getting up and running. I have a question about the parts conveyor. I have figured out the M code to get the parts catcher itself to pop...
Hi All,
I just wanted to give everyone and update on this post and put it to rest. I ended up finding the small ribbon cable leading from the "soft key" function buttons under the LCD screen was...
John,
I am attempting to work on my post processor to make the code look for like what you posted. However I was wondering if you knew if my machine doesn't have a C-axis like I had stated will the...
Another thing. I see that this code has a G17 in it. So far I have had to take out any G17 in the code I have tried our else I get an error/alarm saying incorrect plane. Not sure why however...
Thanks John. I will give that a try. As always your the man!
Clinton
Hi all,
Can anyone post an example of a direct tapping piece of code. It has the seicos 21L controller. So far I have been able to use a generic Fanuc post processor for the turning opertaions,...
Thank you for the response. Any idea on what kind of oil is supposed to be used?
Hi,
I have a few questions about the "eco-pack" linear bearings on my TS15 lathe. I havent been able to find much about this but have roughly gathered that they dont require any lubrication or...
John,
Any other thoughts?
Thanks,
Clinton
The machine is new to me and was moved a couple hundred miles in placed in my garage. I just got power to it about 3 weeks ago and it has been working fine. I went through and made sure all the...
Thanks for the reply John. Your right on the money with the labeling of the boards on my machine. Unfortunately I have already tried all the above while I was waiting for a response. Any other...
Hi,
I am in need of some help. I have a 1998 Hitachi Seiki TS15 lathe with seicos sigma 21L controller. The issue is the keypad stopped working all of a sudden. The section on the left side...
I recently purchased the same bar feeder to run with my also newly purchased used hitachi seiki lathe. I have neither up and running yet however I just called LNS and they emailed me the manual for...
I watched the video. Thanks for your help.
Ok, Thank you for your help.
Hi,
I have Edgecam 2012 revision 1. I ended up having my post processor add a G17 before the hole cycle which worked like a charm.
I now have another question. Is there a way to add a new CPL...
Thanks for the reply,
I actually tried running the full program today, everything went well until it got to the hole cycles. It did a rapid into the foam I was cutting then did a slow feed move...
Hello,
I am having an issue in a hole cycle in edgecam. When I load the g-code into
Mach3 i get an error that says "r number less than y value in xz plane.". The only way
I can get by this is...