584,830 active members*
5,630 visitors online*
Register for free
Login

Search:

Type: Posts; User: stonix

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,365

    Re: Stone and granite CNC bit recommendations?

    search for vacum brazed diamond router bits on internet.
  2. Thread: z axis creeping

    by stonix
    Replies
    3
    Views
    3,014

    Re: z axis creeping

    Solved !
    the encoder was slipping in the motor shaft. ccc
    Thanx to awerby :-)
  3. Replies
    0
    Views
    455

    need a suggestion how to mill

    Can I "program" in Vcarve ( vectric) up and down movement while i cut through the stone.
    Here's a link to a video that shows this. Watch from 0.15. to 0.30...
  4. Thread: z axis creeping

    by stonix
    Replies
    3
    Views
    3,014

    Re: z axis creeping

    ok. i will check. (there are a lot of vibratons) . It is symptomatic that the Z axis always creeps UP.

    Spindle cable is separated ....
    I grounded the "servo control casing", but not the...
  5. Thread: z axis creeping

    by stonix
    Replies
    3
    Views
    3,014

    z axis creeping

    Hi. The Z motor (dc servo) does not hold the position while cutting.
    I noticed on a belt that the motor is retracting during operation and as a result, the axis is raised a few mm in the end.
    ?
  6. Replies
    5
    Views
    1,474

    Re: mach 3 jogg problem

    False alarm :-)
    The keyboard was full of dust, and caused "problem"
  7. Poll: Re: DIY Marble - Metal Machining 3 axis CNC Router

    Very nice. Double or triple linear rails on one axis require very high mounting precision .
    On your Y axis i would move the ball screw lower, to be "closer" to the tool.
  8. Replies
    5
    Views
    1,474

    Re: mach 3 jogg problem

    Is anyone familiar with this "problem". :-)
    When I press arrow key to move ( for example) in Y+ direction and at the same time press other arrow key to move to the X+ dir, the machine does not...
  9. Replies
    17
    Views
    5,417

    Re:

    You have to instal additional input languages, and then switch between them.
  10. Replies
    17
    Views
    5,417

    Re: Single Line Fonts, how to get them

    Serbian Cyrillic Single line font, created in StickFont Editor .
  11. Replies
    22
    Views
    5,837

    Re: Engraving Granite?

    I use Astech router bits for hard granite 90 degrees.I buy them over the internet- aliexpress. I think its vacum plated diamonds.
  12. Re: mach3 - Z axis counter shows unspecified values

    People thank you very much for taking the time to answer.I have home made machine, and im engraving letters in stone . its dc servo motors/drivers. I started to pay attention to above mentioned...
  13. mach3 - Z axis counter shows unspecified values

    Hi . A few days ago i have noticed that Z axis counter in mach3 does not display correct values which are set up in safe Z and other settings, and Z axis does not "keep highs".
    For example:
    when...
  14. Replies
    22
    Views
    5,837

    Re: Engraving Granite?

    Hi, I have handmade cnc machine and I use it for engraving letters in granite for a year, ( nero assolute, red africa...the hardest granites) . For now, I use incimar bit , but I intend to try vacum...
  15. Replies
    11
    Views
    5,090

    I reinstaled XP as standard PC , but "grapf" ...

    I reinstaled XP as standard PC , but "grapf" has not improved, so I purchase another PC and everything is going well.
  16. Replies
    11
    Views
    5,090

    Thanx, Variations are going from 25014,25015,...

    Thanx,
    Variations are going from 25014,25015, 25016, 25033, 25032... The most frequent are 25015/25032. The oscilations on grapf are uniform, but its not STRAIGHT line?!

    I use PC , windows XP,...
  17. Replies
    11
    Views
    5,090

    Hi, can you tell me is this ok: 223632 Proc 1,8...

    Hi, can you tell me is this ok: 223632
    Proc 1,8 GHz
    RAM 1 GB
Results 1 to 17 of 17