584,837 active members*
5,452 visitors online*
Register for free
Login

Search:

Type: Posts; User: tturnbull50

Search: Search took 0.00 seconds.

  1. Replies
    166
    Views
    36,561

    Fanuc 12 M Manual

    Does anyone know where I can get a Fanuc 12 M programming manual?
  2. Replies
    8
    Views
    1,449

    Checked them all, seems ok???? This fault is...

    Checked them all, seems ok???? This fault is intermittent, runs fine for several weeks then just losses m/c "Z" zero.
  3. Replies
    8
    Views
    1,449

    Fanuc OM-Ic

    Has anyone ever experienced the loss of machine zero reference points? Always seems to be Z zero and about 52>53 mm short of correct point, but no ALARMS caused major crash. This is driving me nuts...
  4. Replies
    2
    Views
    1,114

    try OSG, have used their drills and taps

    try OSG, have used their drills and taps
  5. Replies
    16
    Views
    1,364

    OSG do metric taps as well been using them for a...

    OSG do metric taps as well been using them for a while try their website
  6. Replies
    4
    Views
    2,124

    Fanuc pocket milling macro

    Have been trying to make a rect. pocket milling macro, so far as below but only if X is greater than or equal to Y, but can be rotated.

    If anyone knows of a better way can they please post it.

    ...
  7. Replies
    6
    Views
    1,425

    Yes, during tool change when machine crashes tool...

    Yes, during tool change when machine crashes tool recovery states move to tc Zero but actually moves to Machune zero difficult to remove tools from arm during this, service engineer doesnt know why...
  8. Replies
    6
    Views
    1,425

    Fanuc 18 model B

    Fanuc 18 model B
  9. Replies
    6
    Views
    1,425

    Stevo thanks for the prompt reply already doing...

    Stevo thanks for the prompt reply already doing it just wondered when the other machines dont require it, got another problem with tool change, on another forum, thanks again
  10. Replies
    0
    Views
    1,368

    Mitsubishi M-H5B

    Help needed; Fanuc 18 m, when machine crashes out (at tool change) and tool recovery page states that you need to return to T.C. zero, it actually needs to go to "machine zero" which is rather...
  11. Replies
    6
    Views
    1,425

    M01 Help needed

    Is there a parameter that allows the machine to restart the spindle etc. after a M01, as the machine I am currently using does not, but another one does.
  12. Replies
    22
    Views
    4,023

    thread milling macro

    Try this I use it on fanuc O-m +18 both vert. and horz.
    You only need adjust first 6 lines of :4000 it takes care of cutter comp.

    T1
    M6
    G0G54X0Y0S2000M3
    G43Z100.H1M8
    M98P4000
    G0X50.
    M98P4000
  13. Replies
    5
    Views
    1,014

    thread milling macro

    try this I use it on fanuc O-M + 18
    It is in metric but can be used for imperial as well

    T1
    M6
    G0G54X0Y0S2000M3
    G43Z100.H1M8
    M98P4000
    G0X50.
    M98P4000
  14. Replies
    29
    Views
    4,536

    Have tried all suggestions original prog did not...

    Have tried all suggestions original prog did not have 2 decimal points dont know why it copied like that, but machine would have brought up an alarm if it saw that, when machine stops there are no...
  15. Replies
    29
    Views
    4,536

    Part of a much larger prog, the rest run fine but...

    Part of a much larger prog, the rest run fine but for some reason this one doesnt, mostly programmed offine via copy and paste, so loop works but on this one???? just wondered if there was a...
  16. Replies
    29
    Views
    4,536

    Thanks for speedy reply

    Daewoo, fanuc o-m control,
    T100
    M6 (TAPPING DRILL 1/4 BSP)
    #1 =54
    WHILE[#1 LE57 ]DO1 (No OF OFFSETS)
    G90 G0 G#1 X0. Y0. S1500 M3
    G43 Z100.H100 M8 T101
    G83 G98 Z-24.R5.Q14.5.F300
    G0 Z100....
  17. Replies
    29
    Views
    4,536

    Machine freezing

    When running a programme the machine freezes on a particular tool, after reset, it runs, after pallet change it drills one hole then freezes again, NO alarms. I have tried changing the tool No etc.....
  18. Replies
    4
    Views
    1,668

    :4001 (HELICAL) G21 G40 G80 G90 G0 G54 G90 X0...

    :4001 (HELICAL)
    G21 G40 G80 G90
    G0 G54 G90 X0 Y0 S2000 M3
    G43 Z5.H3
    #100 =-20.(FINISH DEPTH)
    #101 =10.(RADIUS OF CUTTER)
    #102 =30.(HOLE DIAMETER)
    #103 =150 (FEEDRATE)
    #104 =5.(PECKING...
  19. Replies
    1
    Views
    981

    Try this, I use it on a fanuc O-M system ...

    Try this, I use it on a fanuc O-M system

    :5555 (LINK PROGRAM)
    #531 =1 (pallet 1)
    #530 =54 (G54)
    P1111 M98 (Prog No for PALLET 1)
    M62(change pallet)
    #531 =2 (pallet2)
    #530 =55(G55)
    P1111...
Results 1 to 19 of 19