509,582 active members
4,091 visitors online
Register for free
Login

Search:

Type: Posts; User: phamandp

Search: Search took 0.00 seconds.

  1. Thread: Proma SD THC

    by phamandp
    Replies
    1
    Views
    60

    Re: Proma SD THC

    Hi Shayne367
    Try adjusting the SPE down mate. I'm using THC proma SD too :).
  2. TNG stepper motor configuration need help!

    Hi everyone, I have a problem with my stepper motor configuration on TNG software, could someone please to help me?. Thanks a lot.
    When I used the rotary axis for cutting the round tube by plasma,...
  3. Thread: THC problem

    by phamandp
    Replies
    0
    Views
    13

    THC problem

    Hi everyone,
    Now, I have a problem with my THC ( proma 150 SD) it always driver the torch contact with the material surface, I don't know why, I have already tried with another settings but it is...
  4. Sticky: Re: Floating Z axis head with PlanetCNC TNG [3D print files included]

    Hi PlanetCNC,
    In this clip ( please see picture below) where is the end of each wire of material probe switch ? If them connect with the controller how can I do it? Could you show me please? Thank...
  5. Replies
    7
    Views
    175

    Re: THC G-code problem

    Thank you a lot rodw,
    I just need to connect the pin 12 & pin 14 on the hypertherm cpc port to the GDN& OK input pin ( config input pin 3) on the MK3 controller, right? ....
  6. Replies
    7
    Views
    175

    Re: THC G-code problem

    Thanks for your replies,
    I have already checked and recongnized that a OK arc pin hadn't been connected, but I did'nt found the wiring diagram for a OK arc output with Cpmpact THC SD (proma) in...
  7. Replies
    7
    Views
    175

    Re: THC G-code problem

    Hi PlanetCNC,
    I have already connected the THC (Proma SD) with plasma source (Hypertherm 45XP) dirrecty as your guide on the blog but the machine just only ran over the THC code line a little bit as...
  8. Replies
    7
    Views
    175

    Re: THC G-code problem

    I got it. Thanks you very much.
  9. Replies
    7
    Views
    175

    THC G-code problem

    Hi everyone, I have a problem with THC G-code. When I uploaded the G-code in Planet TNG software and started to run it, the program just only ran a little bit and stopped at N51 line. I don't know...
  10. Replies
    5
    Views
    50

    Re: USB Controller MK3 stepper setting

    The driver with adjustable current from 0.25-1.4A and it was supply 220V Voltage. You right! the motor seem to be overload even though I use gear box with 3:80 ratio. About losing steps on some axis...
  11. Replies
    5
    Views
    50

    Re: USB Controller MK3 stepper setting

    Thanks you harryn,
    About my A Axis rotary configuration:
    + Driver Vexta RKD514H-C set at 0.18 deg./step and 1.4A current.
    + Motor Vexta PK596 with 0.0144 deg./step resolution 1.4A current max and...
  12. Replies
    0
    Views
    355

    Re: powermax 45 proma thc150 HY-JK02-M 5

    Hi BFS, you can use relay in the HY-JK02-M 5 cnc card to start/stop the plasma source.I have never used HY-JK02-M before but I had already saw it on the internet. Some link may be useful.
    Wire JK02...
  13. Replies
    5
    Views
    50

    USB Controller MK3 stepper setting

    Hi everyone! I have a problem with my CNC controller setting ( I use Planet CNC USB Controller Mk3). My CNC machine have 4 axis ( X axis set axis 1 port,Y axis set axis 2 port ,Z axis set axis 3...
  14. Replies
    2
    Views
    88

    Re: Planet CNC without THC Option

    I got it, thanks you alot.
  15. Replies
    2
    Views
    88

    Planet CNC without THC Option

    Hi everyone,
    I'm An. Now, I have I problem with Planet CNC TNG software. I tried to activate THC Option in Planet CNC TNG but I did't find it anywhere. Could everyone please to let me know: "how to...
  16. Replies
    14
    Views
    1,552

    Re: MK3 / CNC USB Controller - Plasma Stuttering

    Hi guys, Could someone show me how to connect the hypertherm CNC cable to the MK3 please? Thanks a lot.
Results 1 to 16 of 16