You also have to set the network card in your PC. If you have set the UC300 to 10.10.10.11 then set your PC to 10.10.10.10/255.255.255.0.
Edit: Sorry, I didn't see the answers...
Type: Posts; User: dezsoe
You also have to set the network card in your PC. If you have set the UC300 to 10.10.10.11 then set your PC to 10.10.10.10/255.255.255.0.
Edit: Sorry, I didn't see the answers...
Hello Steve,
The code I wrote you must work. I use it since many years, it was one of my first settings.
Edit M99998.txt and insert these lines:
...
The 1.21xx series is in development state, so always use the latest of them. It is now the 1.2111 and you can find and follow it here: forum.cncdrive.com • View topic - UCCNC test releases posted in...
Goto Zero executes the M204.txt macro. This reads the SafeZ value from the Configuration/General settings page and tries to go to that position, so check this setting. After the Z movement it goes to...
I corrected some logical errors, but I'm not by a machine, so I could only test in demo mode. Please, try it and report the results.
BTW, which last version do you use? (1.2049 stable or 1.2111...
Which macro do you want to work with? (The 2 macros you uploaded are not the same.)
We've made 2 new special offers, details below:
Motion controller + breakout board combos - CNCdrive - webshop
The offer expires on 15-10-2019 or while the stock lasts.
Please share on your...
Hi,
I can't tell you.We are working on it. Register on forum.cncdrive.com • Index page and there you'll see it.
Hi Eddy,
We debugged and found the reason for the problem.
We fixed this issue now and will be fine in the next development release.
If you need a quick fix then put a short dwell (G04) after...
OK, thanks, it works! I got 3 bad runs of 10. That's enough.
Hi,
Not yet. It's not so easy to find something that happens only sometimes. I saw the problem on the first run of you code, but never again. First I have to find the conditions that cause the...
Hmm. Interesting. I saw it one times and it doesn't depend on the settings (profile), because I saw it with my profile. We'll try to find out something.
Hi!
Which UCCNC version do you use? Can you post your profile (.pro) file?
I don't think so.
We are doing a special offer till the end of August 2019 for each UC100 sales we give a free UCCNC software license key!
The special offer is only valid for new UC100 purchases only through our...
The direction positive set the homing direction only. That is why it is in that line of settings. E.g. you have an X axis and a home switch on the nagative side. The homing will start to the negative...
Do you have UC200, UCR201 or XHC-HB04 pendant? If yes, turn off the plugin that the pendant uses.and try to probe again. Tell us the result.
When you touch the probe you can simply enter the height of the block to the Z DRO.
The AXBB has a plus port also. You can connect there a BOB (UCSB or HDBB2 or any other cards) and you have more 12 outputs and 5 inputs. Above the low quality motor drivers most of them have...
Thanks! At the DB25 connector there are 2 switches. Is the switch 2 ticked to "ON" position? If not, then you need to set the charge pump output to port 2 pin 16 in UCCNC/Configuration/IO setup.
And don't forget to upload your profile (.pro) file from UCCNC\Profiles after pressing "save settings"!
I use a tablet daily with UC300ETH or UC400ETH. I have a USB2 to Ethernet adapter to connect them and I never had network errors. (I have a USB3 adapter too, but the UCxx controllers work only...
Check the latest (1.2108) test release. It's not recommended for production, but it has a probe screen that does all you need. The next test release is coming soon.
Is that .Net package good for Win10? On Win8 or Win10 you should install .Net 3.5 in the "Turn Windows features on or off" window by selecting .Net 3.5. Just press Start and type "optionalfeatures"....
I checked the MX4660 manual. It sees the world form inside. :) When you connect something to its input, you have to check the DB25 (CN1) table to find that which output connects to your input. So,...
You also have to select port 1 when setting a pin. Input pins are 10, 11, 12, 13 and 15. The UCCNC zeros the port and pin if you enter an invalid port/pin pair, or try to assign an input pin to...
It is a false positive. While installing, disable Defender. When the setup is ready, exclude the UCCNC folder. Disabling Defender is a temporary solution, because when Windows starts it will be...
Of course, you can. You can make it as Gerry wrote or you can build your own. The latest stable version 1.2048 has an updated OSK plugin which also supports MDI input, not only numbers.
Also, you...
I think, that the elapsed time resolved the problem. If there is a problem with the licence file, you get a licence error, not communication. Maybe, the UC400 needed more time to find the network...
Chuck,
How did you reset UC400? Did you press reset while no power on UC400 and released only after the power was on again? The UCxxx_utility should find the UC400 if they are on the same network,...