Search:

the question is the open and close time most ER collets use a nut that holds the collet.
So a wrench is needed. Or maybe the tommy bar is like a collet closer so all you need to do to feed the bar...

Hanita varimill

This would fall under the five yaer rule. What would be the split in the wages in five years. And which one would have more loyalty to you. I would rather have a long term than a short shot in the...

i think it may have bin mentioned above some where, but what the heck I chip it back in.
There are 3hp peak and then there is 3hp cont. most 3hp peak are raely only 2hp.

Also dont forget about...

It looks to me like it needs to be "V" cleaned and tig welded. And leave the weld bead proud. Do find out the correct material type
I have to agree with mactec54 it realy never got welded to begain...

inverter vrs transformer type. How the Heck do they get the power from a suit case that used to take a 300lbs welder to even come close. One advantage of the older transformer welders are they dont...

Like bubba said bored jaws will work. I asume you are worried about the stock falling out between the chuck jaws at least thats bin may dismay with the small stock VRS. Big three jaw chuck. The only...

look at a CCGX insert design and you will see what it takes for relive angles.

also tubing can be tricky (lack of regidity) so very small radi (430-431) and low IPR of around .003 DOC will depend...

turning the shaft, look into hollow mills maybe even customize it for the head as well
one plunge in Z and part off with a oh say .06 inch wide L or R insert and even then it will most likly leave...

we use Sandvik super fine adjustments into the .00008 range. capto mount $$$$$

one must look at the min required doc and feed for the chip break and ask yourself if the machine has the power and regidity that it would take. We use them all day long and love them and yet I have...

G75 I think was is full circle ability. Hum may have to do with end piont tollerance.
can you post a drawing of your part with dims and origin? Just at a glance somthing looks off in the centers of...

generaly geometry beats brute strenght. Also keep in mind any thing that moves has a clearance value and multiply that by the distance.of the arm.... .001" ok not bad x 10 inches arm length now makes...

might check J&L I think they carry one thats called Debur Master. same thing dif name.

looks nice do the o-rings flatten down all the way???

air powered venturi vacuum generator.
is right.


sorry about that

when i make vacume fixtures I make a scroll (spiral) in the pockets pending thickness of the material for the spacing of the walls. then on the outside (not connected) cut an oring groove. The groove...

I just use steel pallet strap and bend a little a viola. Its cheep and is every where.

it works great.

just thinking what effect would the flux feild have on the stepper motors and or spindle motor. Not to mention the cleaning of a bed of perm. mags would be a pain.

Just thinking out loud.

have you looked into AME the SAFE line of tooling? Lots of cool self aligning clamps and blocks.

resolution is set by the angle of each step on the motor and the gear raito and or thread pitch of screw.

You have to tell the software how many steps = an inch

anti backlash takes the end play...

The rails have to run true to each other, so I would build them with that in mind like a set of linear rails then attach to the router table and set square with other rails. I think the easy way of...

From my exsp. use three bearings on each side of your angle. Two on the load side and one on the buck side this aviods the binds caused by thickness changes in the rail. The rail will flex slightly...

Bsiniard,

Pm me with your fax number and I will get a copy of the "G" and "M" codes to you

look up "mity bite" as the make a low tepm glue just for this type of job. J@L MSC......

AMflex

try trim or keep and then select the line for edit, then hold down ctrl key and then select the lines at which you want to keep it at or trim it at

Have you used the park tool at least that is what I have done for like pallet change, part change or check op stops. off part that is not mid cycle.
Esprit will recognize end and mid pionts in the...

we have always had good luck with Esprit and Their support. If possible take the Post programing class and custom tweeking is painless mostly. In the Least they will let you change your own post...

look in the hanson rivet book or web page see if it looks like it.