584,812 active members*
5,484 visitors online*
Register for free
Login

Search:

Type: Posts; User: meckardt55

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    1,059

    Re: cnc arrow 750

    If it is an Arrow 750, I think it should have an A2100 control, not a CT control. Can you clarify this??

    MIKE CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine Services
  2. Replies
    3
    Views
    2,468

    Re: Cinci A2100 password reset file

    This is a procedure for the password reset but does not have the software


    Re-setting A2100 Passwords to the Factory Default Settings
    This procedure is valid for A2100 controls with both...
  3. Replies
    8
    Views
    1,890

    Re: Increase memory - Acramatic A2100

    If you did not purchase the network option, you must go through windows NT to set it up. If you look at the option screen it should tell you if the network option was purchased.

    MIKE CNC...
  4. Replies
    6
    Views
    1,199

    Re: Cincinnati Arrow 750 spindle overload

    I would remove the contactor and take it to an industrial electrical supply company to size it up for the voltage and current. You can use any similar contactor with the same rating and coil voltage....
  5. Replies
    3
    Views
    2,468

    Cinci A2100 password reset file

    We need the file to reset our password for the Cinci Arrow A2100 control, Thanks
  6. Replies
    30
    Views
    3,001

    Re: Falcon200 X axis alarm 44-45

    What control do you have? What color are the drives? How fast were you jogging the axis when it crashed? Can you hear the brake clicking when you start the machine the second time? You need to check...
  7. Replies
    2
    Views
    685

    Re: Cincinnati 750 sabre

    You need to give us much more info if you need our help, a little more detail would help.

    MIKE CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine Services
  8. Replies
    15
    Views
    2,152

    Re: Falcon 200 acramatic 2100 issue

    You need to send it to FIVES machine company 800-934-0735 to get it re-flashed about $500 last time I checked. What was the DC voltage on the battery?

    MIKE CNC Machine Services INC |...
  9. Replies
    15
    Views
    2,152

    Re: Falcon 200 acramatic 2100 issue

    It looks like the RT board failed. You can take the right hand board out of the control and check the battery but don't take it out!!! The battery should be over 3 vdc put the black lead on the...
  10. Replies
    5
    Views
    1,084

    Re: Arrow 750 Part out- parts for sale!

    What control and drives are you using for your retrofit?
  11. Re: Cincinnati Arrow 1000 CNC machine retro fit

    If you have electrical prints it should show that the resolvers are in the motor and if you have the BLACK color drives(KOLLMORGAN) the drives convert the feedback from the resolvers to encoder...
  12. Re: Cincinnati Sabre 750 X-Axis Ballscrew Replacement Procedure

    Found out how to attach a file for your problem someone wrote this info, good luck

    MIKE CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine Services
  13. Replies
    2
    Views
    728

    Re: acramatic 2100 program

    Greg,
    Can you send me the same info please. You can e-mail it on our website under contact, under our phone #. Thanks

    MIKE CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine...
  14. Re: cincinnati saber 750 axes drives are not enabled

    I think you are looking at the FOLD BACK light. This indicates the axis is in a over current condition. If you brace up the Z axis with a 4x4, turn off all the power and disconnect the 3 axis drive...
  15. Replies
    4
    Views
    1,073

    Re: y axis error

    Which wire is damaged??? Give me some more detailed information and we can help you.

    MIKE CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine Services
  16. Replies
    2
    Views
    599

    Re: Falcon 200 Help

    You may have a 24VDC short in the inputs or the outputs on the machine. It sounds like the problem is not in the boards but in your machine.

    MIKE CNC Machine Services INC | Cincinnati Milacron...
  17. Replies
    4
    Views
    1,073

    Re: y axis error

    It looks like the axis is enabled but the analog from the control is not correcting the drift in the axis. Check the connections on the drive and the red and black wires (analog) from the control.
    ...
  18. Replies
    9
    Views
    1,119

    Re: New Cinci Arrow 500 problem

    Let us know what you find and what corrects the problem. I have also seen air compressors starting causing this problem. Was the X,Y, and Z axis secured during shipment?

    MIKE CNC Machine...
  19. Re: Sabre 750 Acramatic 850SX tool change point

    In normal operation all switches should be off ( to the left ) but to get into the parameters you need to turn on the top switch #1 to the right ( on ) to get into service. Take the small black...
  20. Replies
    15
    Views
    3,582

    Re: Spindle Failed to Stop, Alarm 39-37

    Did you look at the fault codes using motion link connected to the spindle drive, it should give you a reason why the spindle faulted. Did you monitor the DC bus voltage when this problem is...
  21. Re: Acramatic 2100 servo failed no pass diagnostic

    You may want to look at the 5vdc going to the encoder ( depending on the kind of drives ) for the X axis along the Y axis cat track. The 5vdc could be shorting out and causing the problem on the dv5....
  22. Re: Avenger 250MT - resolver kicked bucket - options

    Try to contact Greg Wood on this site, he may have a solution. Maybe you could use the spindle motor encoder??. The original feedback was from Heidenhain Corporation (847) 490-1191, you should...
  23. Replies
    8
    Views
    1,051

    Re: Acramatic 2100

    I am not sure this is a Siemens A2100 control, looks more like a CT control in dos.

    MIKE CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine Services
  24. Re: It’s been a while still initializing found this though

    I could not open your attachment.

    MIKE CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine Services
  25. Re: Arrow 750 - Alarm 40-33 Output/Fuse Failure in APC Rack 0

    When you remove the battery on the RTC board you will loose the BIOS. You will need to re-flash the BIOS or send it to FIVES machine company for a re-flash 800-934-0735 it is about $500.00

    MIKE ...
  26. Re: Arrow 750 Aramatic 2100 HDD problem Please Help need backup

    When a newer version of Windows first encounters an NTFS volume, the operating system automatically
    updates that volume to the current NTFS version (NTFS 5). If an A2100 hard drive loaded with...
  27. Re: Arrow 750 Aramatic 2100 HDD problem Please Help need backup

    If you used a newer version of windows and your machine software is older then 4.0 sp6 then it upgraded to NTFS file system and the control will not see it. You must make a IMAGE of the drive and not...
  28. Re: Arrow 750 - regen resistor glowing red hot.

    We suggest that you send the unit and call Kilroy Corp. 937-660-5313. We have used them for years with Kollmorgan drives and have been very happy, they are in Dayton Ohio.

    MIKE CNC Machine...
  29. Re: Arrow 750 - regen resistor glowing red hot.

    Do you have black Kollmorgan drives? If so, it could be that the DC bus voltage is to high, it should be about 320 VDC. The regen resistor may be trying to keep it lower if it is a lot higher 380...
  30. Replies
    2
    Views
    951

    Re: turret overload alarm

    What turret do you have and on what lathe model. If you don't give us more info, we can't help you.

    MIKE CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine Services
Results 1 to 30 of 500
Page 1 of 17 1 2 3 4