I was wondering if anyone could recommend a place to buy abba linear blocks brha25's i only need 2 of them, the place i had ordered from originally does not carry them anymore :(
Thanks
Type: Posts; User: elogicca
I was wondering if anyone could recommend a place to buy abba linear blocks brha25's i only need 2 of them, the place i had ordered from originally does not carry them anymore :(
Thanks
Nope it's probably from you vfd & spindle causing interference!
Going to try and pinpoint it, spindle powered off it runs like a charm never hits a 0.005 following error
Could this just be from bad tuning?
Ok I have a g320 running an 850oz servo with a ballscrew, I am also using the sound logic encoder interface, everything is shielded wiring.
In mach 3 i'm running a peck cyccle and checking the...
If you do it in a plugin you can use any of the available protection systems or roll your own.
Chris
You'd be surprised what will react though when you get to flame polishing, even acrylic polishes respond bad to it.
Imo I would not put any detergent near acrylic, if he was to put detergent then cut then flame he would get crazing.
I use onsrud 2 flute downcut, great bits give a great finish 18,000rpm 160ipm 0.165doc.
But i do get some chatter on the edges, if an optical finish is needed you have to sand.
I imagine a 100%...
I was wondering if anyone has had any dealings with them lately? I placed an order 2 weeks ago and my order status has never changed from confirmed to shpped. Also no replies via email.
Chris
Well got DeskCnc running great now, I;d have to say retrofit time was much better than camsoft.
I have Been talking to Carl at DeskCnc quite a bit, and must say his support is great. He is...
Well some of you may have seen my experience with camsoft. Well it turns out their 400$ stepper board is the same board as DeskCNC, except they don't support the extra features.
So today i...
Just doing some homework it seems on deskcnc that your limits/estop and probe can be no or nc type. But what about homing? all my switches are no. is there a way to still use them as home switches?
Actually, the biggest issue is limit/home switches. one guy says raise decel the other says lower it, both say it's impossible for the controller to stop on a limit switch.
Oh and a side note...
Well I for one would rather shoot myself in the foot then to try and re-install my Camsoft system.
Yes there is one neat option about the software in that it is fully customizable g&m codes.
...
Does anyone here have an rs232 analog module? any idea how to set it up?
Chris
Ok time to fix up my machine when doing 3d i get jerky moves i was considering flashcut or camsoft, but them i came across emc using a 5i20 with softdmc. Is anyone running this config? how does it...
Man, that would be alot of work..... basically i hear a rumble on long fast travels.... I got a squeak to get rid of too :) i lost some block balls on an over travel once....
Geeze you guys and your pictures :)
Will take some after the holidays, modifying mach3's screen set for my stubby fingers lol.....
:) New pendant I got tired of walking over to the pc screen.
Had an old little touch screen, add a mpg and there you go.
http://www.cncmarinesupply.com/images/forums/newpendant.jpg
Can emc2 handle dual home switches on a gantry for homing?
There are allot of differences between a spindle and router. I believe it costed just under or over 2k.
I used to run routers but the bearings died too often....
Also the spindle creates 1/2...
I have zipped up the mach plugin source and ccs c source for the pic. I'm running it on a 18f4455 using usb transfer.
As for a schematic it was done on the fly.
Please I don't want to sound...
Estimated cost descending :)
Rails
Spindle & VFD
Motors
Electronics (Bob, Gecko's, Ps)
Alum
Wiring
Steel
Bolts Lots of them (I think there's about 500 or so socket cap screws!)
The sdk is really easy and you could make a user config screen to set the ins and outs. I got a graphic lcd but it's reserved for another project :)
For mpg's the sdk is much better...
I just bult myself a pendant using a pic and usb, i opted for bulk transfer and using the mach sdk directly much faster.
http://www.cnczone.com/forums/showthread.php?t=37267&page=8
As soon as i get some extra time, there are no schematics :) did it on the fly knew what i wanted.
I want to post up the pic code & hex and the mach plugin & code....
Too much to do so little...
Well I've been wanting to do this for quite a while finally did it. I built a pendant for mach 3 and my machine it works great.
Details
4x20 Lcd Display
Driven By A Pic
Usb Powered...
Well it seems that if i don't run mach 3 the instant the desktop is up it's fine...
Guess winblows is not quite fully loaded at that point.
maybe i'll take some update pics too today, The motors are more than adequate :) i wouldn't want to get in the way of my gantry. i think i am getting somewhere around 1900 steps per inch i can rapid...
Well first off I would of gotten the steel ground for the rails to be mounted on.
I would also increase the gearing to up the resolutions.
Aside from that not too much runs like a charm. nice...