GOOD DAY GUYS.
I AM LOOKING FOR A BACKUP FOR A KAFO V-2175 WITH A FANUC SERIES 15M CONTROL.
ANY ASSISTANCE WILL BE APPRICIATED .
THANK YOU
495010
495012
Type: Posts; User: jacof
GOOD DAY GUYS.
I AM LOOKING FOR A BACKUP FOR A KAFO V-2175 WITH A FANUC SERIES 15M CONTROL.
ANY ASSISTANCE WILL BE APPRICIATED .
THANK YOU
495010
495012
The machine is a PUMA 8HC-3A. The control is Fanuc o-T with Alpha series servo drives.
Machine serial number is :3P080124
Any help is much appreciated thank you.
Good day guys. Got a Puma 8HC-3A. Lost all parameters. Tried getting from local agents, but no luck. Started sorting it out and are now stuck in spindle parameters. If i start spindle, only loadmeter...
WAITING FOR A REPLACEMENT DRIVE CONTROL BOARD.
WITH ALL THIS CRAP COVID , IT MIGHT TAKE FOREVER.
GOOD DAY GUYS
HOPE ALL IS WELL.
I HAVE A CUSTOMER THAT LOST THERE PARAMETERS ON A DAHLIH MCV-1450 WITH FANUC 18i-MB CONTROLLER.
DAHLIH WAS CONTACTED , AND WE WERE INFORMED THAT THEY LOST THERE...
Hi richardfp4
Thank you for the reply.
Yes they are very happy with the machine.
The only trouble we get on this machine , has always been on the Mitsubishi servo turret.
Would appreciate...
GOOD DAY GUYS.
GOT A CLIENT WITH A SMALL JENN-WEI CNC LATHE. FANUC O-TD CONTROL,
HAVING PROBLEMS WITH THE SERVO DRIVEN TURRET.(MITSUBISHI SERVO)
FAULT TRACED BACK TO WIRING ON MACHINE.
...
Good Day
Please can anybody help me with the datasheet for a Hitachi Seiki VA-40 Micon 8 system? All data was lost due to low battery.
I am situated in South Africa. You can email me,...
Hi jdeere4250
Sorry for the mori thing.
I think it is the Micon 8 Model II (SQM8). it only has 1 switch on the CPU Board(WRSW).
Your help will be appreciated.434736434738
Good day and best for the year ahead.
Guys, i got a problem i hope some one out there can help with.
Mori Seiki VA-40 MILL with a FANUC 6 control and assisted by a MICON 8 driven ATC.,
...
UP DATE>>>>>
I am glad to say i can now repair most of the problems on these Mitsubishi MDSASPJA75RT drives
IF YOUR IGBT IS SHORTED , YOU NEED TO REPLACE THEM.
DO YOU HAVE ALPHA SERIES SPINDLE DRIVE?
THE OLDER AC SPINDLE DRIVE HAD FUSES THAT BLOWS WHEN THE IGBT BLOWS.
THESE USELESS FUSES PROTECTS...
Hi guy's
Just to update.
The servo drive has gone back to the company for further investigation/repairs.
Will keep you posted
Good day Guy"s
Does anybody in the forum know where i can send a Mitsubishi MDSASPJA 75 RT Spindle drive for repairs.?
Got quite a few machines (Quicktec vmc ) in South AFRICA with these drives...
No. IGBT separate and bolt on to base board with circuit.369784369786
IGBT got pins that connect to base board.
Will remove IGBT and see status. Will keep u posted
HI Guhl
Thanx for your reply.
Before i do this , i have to ask.
These are Alpha series drive and the IGBTs got the pins on the side that pushes into the pc board.
Will it not give a different ...
Thanks for your reply.
This is a small Spindle and does not have the high and low circuit winding.
The motor connects direct to the servo drive.
Get the alarm while booting up before the system is...
Are you still having problems?
Hi guys
Got a fanuc A06B-6077-H111 power supply and a A06B-6078-H211#H500 spindle amp.
Had an alarm 5 on power supply and alarm on the spindle drive.( can not recall number)
Both units was...
Hi Craig.
I am always busy and seldom get chance to go on line and try to help people .
Nice to see someone I know on the site.
Was the Diagnostics also loaded when you did the Parameters?
when parameters was restored, did you also reload the Diagnostics?
Can you give me your e-mail details?
That fault normally indicate that the main board did not ""Boot"" up.
The only way to rectify is to replace the main board
Good day guy"s
Got a customer with a Creator EDM Machine.
The P.C had an alarm 'CMOS checksum error - Defaults loaded'
P.C was removed and the Batt. was replaced and the error was gone.
Now it...
Good Day Guys
Can anybody assist with Fanuc Part Numbers for an ai-Spindle Motor Sensor cable or plug. Tyco Electronics AMP make, 2 rows, 12 Pins.
Thanks,
Jaco
Will be THX
Thanks for the reply GITRDUN.
It is a AC Servo system. Will check as you said when i get back to the customer. The agents have already quote on a replacement servo motor , but are to expensive....
Good day guy''s
Can any body out there assist me with a Haas Mill?
Machine works fine. all of a sudden the X-Axis moves very noisy and roufgh . Sometimes it gives servo 103 high current alarms,...
When you switch on , after the software version , the screen should show ;not ready; at the bottom under the 0465-01.
Then , if you release the e-stop button it should show the position screen and...