Thank you for the recommendation. I will look for some of these today.
Type: Posts; User: oxford
Thank you for the recommendation. I will look for some of these today.
Thank you for the detailed explanation Craig.
Since I'm only going to be running about 9 ft max of cable, it looks like I don't need an EMI filter on the output, and I don't really need to worry...
After a decade hiatus, I have dusted off my Yaskawa Sigma II servo drives and have started laying out a control box.
Finding the right parts can be a challenge. The Yaskawa documentation...
Slow and steady wins the race...I hope.
Still in the teardown phase.
In the process of trying to pull the table apart. I have no idea how to remove this knob from the ball screw. Pictures...
Howdy,
Took me a while to get to a point in my life where I could dabble in CNC milling again. Finally have the space to work on a respectably sized mill. A friend of mine at work decided to...
Did you have a particular laser type in mind? CO2, fiber, laser diode....etc?
I know it has been a while since your post, but what is your project and where are you in Brazil?
-Anapolis GO. right now
Used Bobcad V22 for a couple years. Just got V25 a few months ago. All the issues I had with v23 were fixed. The CAD portion of the new version seems a lot stronger computationally than before. I...
Personally, I really like my BobCad V22. I could afford it and it has paid for itself many times over. Simple learning curve too.
Do you have a photo of your setup?
Just to be clear, you have the SS and BOB 32 connected to a 5v power supply?
I think I used a BOB 23 with my SS and even though everything lit up with the SS connected to 5v, it didn't work until...
Is your SS connected to another breakout board?
Just browsing the zone for ideas on fixtures. That is some really nice work you did Geof. Thanks for sharing:P
I'd lurk around for a little and read up on other people's builds. I've gotten some great ideas and advice just cruising through other people's projects.
As for starting out, I used Keling Inc....
Any updates on the project?
Anyone know what the cost per pound is of Zeospheres?
I have had no luck with getting a response from two companies I requested info from.
So far I will limit the I/O for the SGDH to the following twisted pairs:
V-REF SG Velocity control
T-REF SG Connect with resistor circuit to have torque limit option
ALM+ ALM ...
..build isn't dead, life just got in the way for a bit.
Got my manuals printed up at least in the meantime.
I've been amassing parts for a while now and finally am ready to start putting things together.
I will be running some Yaskawa SGDH drives with a Kanalog controller. I want to make myself a...
Thanks for the input.
I have been looking at enclosures to avoid reinventing the wheel. Some of the parts I can't identify yet and wanted to make sure I would not miss out on something important....
Hi Yantra3D
I was looking at your electrical enclosure to get an idea for layout.
What does the grey rectangular tubing do that you have between components. Does it reduce noise, just help...
The drawing I meant to attach earlier :P
When wiring power to multiple drives, can I run some parallel bus lines for ground, live, and neutral and then just twist the wires coming off of them? (As shown in drawing)
Or do I need to twist...
Double check you are powering your optos with the SS.
Try using the recommended 5v, 2A power supply for the drive side.
Scan board for any stry wire clippings that might be causing a short.
...
I had some confusion about the whole power supply to the SS and the output board. What confused me was By trying to get the SS to supply the power to the output board, the voltmeter would read the...
I finally ponied up $25 for some an ER11 set. They fit nicely. Now I just need to test their runout.
Thanks Pat.
I am looking to run one VFD and multiple servo drives.
I see a lot of enclosures using terminal blocks. Are terminal blocks just used to keep the wiring neat?
Is the power factor related to the phase angle between the current and voltage?
Thanks for the advice.
Will one AC reactor clean up the power line for multiple drives?
Are solid state relays not used in industry because of tradition?
How important is an AC reactor?
Thanks :)