Search:

Hey,

Today on the Doosan I over traveled in X running a G84 cycle and of course got a 500 error alarm.
Not usually a problem any other time just move back the axis and hit reset, it happens.
...

Hey, Is there a parameter I can change for the relative coord popup screen in the tool offset page when INP.C is pressed?
Would really like it to be a machine coordinate not relative coordinate!
Is...

Ok so with a good dose of fanuc literature, parameter 3402.6=1 fixed my problem.

Hi All,
Is there such a parameter for a 31i control that after a reset mid program,
all modal G codes cancel or return to start up default.
Cheers
Beaker

Hi All,

Had a drive belt on our mill break recently. Now I have to line up the spindle to the correct position for tool changer, its close but not right.
Which parameter do I change to make M19...

Hi all,

Would like to know if anyone has ever heard of or used this controller SMC4-4-16A16B its available from many places on the web but the guys who have the most info is ChinaPLC.
50KHZ...

Found it, would still like the correct 828D manual though.

Hi all,

We just got a new lathe with the 828D control. Can upload some pictures if anyone is interested.
It has a few dramas but won't get into it now.

What I Want to do is some thread...

At the end of last year we purchased a new vmc with a fagor controller the 8055i.
Have a question about stopping an auto cycle mid way.

Say I wanted to stop the cycle because I had made an...

Hey Zig,

All info is good info, will be sure to check it out. Thanks

What I would like the circuit to do is:
When the power supply's output is shorted a relay disconnects the output and stays...

Hey all,
Have been on the lookout for a schematic kinda like a crowbar circuit but instead of using an SCR and blowing a fuse I want it to pull a relay and disconnect the load.
My fancy lab PSU has...

Hey

I was stuffing around with chooks and I had a try of the version 7 colors chook, now i'm stuck with it.
My question is, how do I change it back to X3

Cheers

Hey, just use axis scaling. If your job is 100mm and you want it to be 0.5mm bigger then scaling factor is P1.005
100.5/100 =1.005

Not sure what control your using, on a Mits it's

G51 Xn Yn...

Hey Michael,

When you say cheap, how cheap do you mean.
Great machine for something like that would be the robodrill mate, IMO
Don't think its what your after but would be a great machine to...

Wow you have your own machine by the sounds of it. COOL!!
How elaborate do you want it.

What about a :
gas turbine,
colt 1911,
homemade nuclear fusion reactor,
Vacuum table for the mill,...

Thanks G-codeguy,

I'm with you, I use Macros where ever I can but for this its just too damn random and large.
Have had a few goes just like you mentioned even tried to use hatching and put a...

Hey all,

I'm doing a job that is an outline of tall grass and flower type shapes on 3/8" flat ally panels. It was to be engraved but now they want a perforated hole look to there panels.
Is there...

There is no problem with the m70 running programs from any cam systems as long as the post processor is correct. For mastercam the mpfan post is fine.
As for the difference between M70 and...

Our new machine finaly turned up V5-XP with mitsubishi M70 controll. But there is a small problem, the navi mill (conversational menu) is in chinese. Can't find anything in the manual to fix it. ...

Hi all,

Have just installed X2 sp1 MC update.
When I pick pocket standard toolpath, in the roughing/finishing parameters I only get two options zigzag and one way.
What is going on? Nothing has...

What I do when its just something small like the part your doing and I have a smaller cutter is, I click on the multipass tab and add multiple roughing passes and modify spacing to suit.

To make a...

Hey,
I hope this is what you were after. I deleted some of your opperations, just kept the ones that were relevent.
Hope this helps ya.

Find your local reseller in your area and get them around to show you the software.
Im sure they will set you up with some sort of demo.

Thanks again for the info guys, gridley that worked great. Scott any info would be of help.
I will update as things progress.

Thanks for the info guys.

Are there problems with the Meau web site, I can't seem to look at any of the manuals or any technical info. It just redirects me to the sales office page.
We do quite...

Hi All

We are looking to buy a new VMC which has a Mitsubishi series 70 controller. I would like to find some info on supported G codes and if it supports macro B.
Cant seem to find any info on...

It all depends on your tap type ie: coated or non coated, thread roller /material.

I run Hahnreiter taps, and usually run it to there specs.
Is that D2 tool steel that you are using, if so I...

Hey suzuki, Glad to hear all is well..

Tapping cycles are very easy.

First consider if you need a spotting drill. I drill one if accuracy is important or if the surface is unmachined.
Adjust...

Hey guys, Just got a spacenavigator.
Will take a little getting use to but so far its good and as for the buttons, more would be better but I didn't want to spend another 100 bucks for the...

That's crazy
Try here
http://www.oceancontrols.com.au/
and I just stumbled on another site
http://www.nollet.com.au/ not sure of his stepper prices, but I have purchased stamp controllers...