Search:

Try X42,C2.
Z-20.

Try Parameter 5450 Bit 1 to 1 . It stops the C Axis jump to C/Line

Each turning tool has 4 index positions.
M481 – Index position 1
M482 – Index position 2
M483 – Index position 3
M484 – Index position 4

So for Example if the quad tool is in station 1 then...

Could you try it from MGI side of things , You should be able to select a Range of Programs in the folder then after pressing the IN/OUT soft key under O List Tab

I am not sure if this is possible on the older S type Puma machines but if it does on a 2013 model .

G100 B control function:
This allows the B axis to perform certain functions while machining....

It sounds like he has inadvertently pressed the wrong button and tried to DNC Set a program. RMT mode is for running programs from Memory card / RS232 . See if there is a soft key called DNC Clear ?...

Doosan supply as standard on Y Axis lathes but it isn't standard in the UK on M Models . It's either specified on order or a Fanuc retrofit.

Has the machine got Helical Interpolation Option from Fanuc A02B-0339-J819 ?

About 6 lines into the milling the Z Axis comes into play ?

Without Helical Interpolation option PS 0021 alarm...

Normally 4 on the 32I are spare for External M code . Check ladder for M91 to M94 and see of they are there .

You are missing the G80 to cancel G84. Program should look like this
G40G80G97;
G00X0.Z2.S200M3;
M29S200;
G84Z-20.R2.F2.;
G80
G00Z10.;
G28U0.W0.;
M30;

Its to do with Lubrication as below . Probably the pump .
https://www.cnczone.com/forums/attachment.php?attachmentid=477046&stc=1

This is correct . It always shows AICC 2 whatever Precision Level is set with the R Value.

Can't be done . You can run from PCMCIA Compact Flash card or drip feed into the control .

Try this . Key in X0 then press the Position Record Button https://www.cnczone.com/forums/attachment.php?attachmentid=469896&stc=1 Then Press the Measure soft key

Yes but a VMC is straight forward X and Y . On the lathe X is diameter so it is double. For example to turn a 40mm diameter on a lathe you program X40. But the tool is only 20mm from centreline ....

I have just ran it through on our machine in simulation and it is producing ovals . Look like a dodgy output from your cam as X is a diameter value its movement should be double in the X compared to...

Hi . Looks like you are in the wrong plane . Try G17 instead of G18 in the 3rd line down . G18 to put it back just before the M99

#6700 bit 0 should be set to 1 for M54 along with #6710 to 54 and to 0 for M30 .

The control will hang on M54 without the being set .

This from Deadly Kitten "cut a face before drilling, so to make sure that the drill is starting on a surface that is perpendicular on it's axis, and also to minimize the start cutting load, since...

Take the cover off at the rear of the spindle . You will see 2 proximity switches . 1 for External Clamp, 1 for Internal clamp . ) External clamp the cylinder moves towards you , Internal clamp the...

Contact your local WTO representative . Its approx £700 list .

This is what we use . Its a dedicated Parting Blade Holder designed to fit around the Lynx Sub Spindle and holds standard 26mm blades . WTO make this one. Nice and rigid....

Looks like the Door Open switch . With it at "1" it allows you to handwheel the Axes for setting up with the door open .. If its never used them I assume you have overridden the safety interlocks.

Parameter 4024 is the minimum RPM for Rigid Tapping on DNM & Mynx machines with OiD onwards . Default is 75 but we have changed it to 20 and had no problems .

Hope this helps

Great News John Enjoy

Hi John

What motor is in the 4th Axis ?

Hi John

14343 is to do with FSSB setting which you should have already done . If so ignore this step.If not then FSSB setup motor ID is the first thing to do.

Parameters 13610/11695 are to do...

Hi motordude

Try this lot .Maybe 1 has been missed out somewhere. Ignore the FSSB settings if you have already done that. Ignore 5th Axis parameters also.

Hope this helps

To be carried out...

Try Keep Relay 8 bit 5 (4th Axis is used). Set to 1 .
Hope this helps