584,837 active members*
5,103 visitors online*
Register for free
Login

Search:

Type: Posts; User: yugami

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    595

    Sold

    Sold
  2. Replies
    1
    Views
    595

    Partner 1E For Sale

    Single board CF computer with upgraded software from Milltronics
    Recently replaced Z axis bearings
    Recently replaced spindle bearings
    Recently replaced drawbar washers
    Recently replaced Y way...
  3. Replies
    6
    Views
    2,510

    Re: VM16F - upgrade VFD/spindle - anyone done it?

    The VFD should run the spindle normally but due to making up the 3rd leg you have reduced max HP before it draws max AMP's

    You do not want constant Torque VFD thats designed for specific loads
  4. Replies
    37
    Views
    6,416

    Where did you hook in when testing? Your 1h is a...

    Where did you hook in when testing? Your 1h is a little different from my E. But did you test from the control pc or by the monitor
  5. Replies
    15
    Views
    3,681

    It was so highly successful it's been dropped...

    It was so highly successful it's been dropped from the face of the Earth.
  6. Replies
    3
    Views
    639

    Re: Replacing Linear Rails

    Mine were so bad you didn't question it. The T portion was more of a knife edge. The head nodded forward around .020.
  7. Replies
    3
    Views
    639

    Re: Replacing Linear Rails

    I did my Z axis. I got lucky and found NOS on Ebay and got it for 350. You have to take some time and learn the THK nomenclature for the part numbers and what they mean so you can see whats...
  8. Replies
    8
    Views
    1,886

    Re: VM16 minimum height with spindle lowered?

    Awesome thanks for the info.
  9. Re: Machine seems to actually work now... What now?

    Never dawned on me I could have x and y home at the same time. Mines Z X Y in that order.
  10. Replies
    8
    Views
    1,886

    Re: VM16 minimum height with spindle lowered?

    Which VM16 variant? Pics? I'm rolling around the idea of a second machine and I'm keeping an eye on the VM16's
  11. Replies
    5
    Views
    1,217

    Re: Partner 1D. Removing X & Y Belts and pulleys.

    I can't find where i had the maintenance section of the Partner series, but they recommend something along the lines of Mobile XHP 222 I believe.
  12. Re: Machine seems to actually work now... What now?

    Do you have tools? Tool holders? Vise?
  13. When I cleaned mine I didn't reseal and haven't...

    When I cleaned mine I didn't reseal and haven't had any issues. Ymmv.

    I didn't stand on the fiberglass but if you run the table forward your can stand on the base to get the nooks and crannies...
  14. Re: Tapping confuses my machine, won't do it, wont tool change after failing

    It was the M29 - I just deleted that line and the test sailed though perfectly.
  15. Re: Tapping confuses my machine, won't do it, wont tool change after failing

    Thanks for the sample.

    Looks like its probably the M29 that the post is outputting. Its a pulsed output and reading the manual a little closer, everything locks up until the corresponding input...
  16. Replies
    4
    Views
    1,035

    Re: Connector pin specs

    awsome thanks
  17. Replies
    4
    Views
    1,035

    Connector pin specs

    I'd like to wire up an air blast and the probe project I finally finished.

    Anyone know the specification on the pins used in the locking connectors on the computer box?
  18. Re: Networking Windows 10 to DOS 6.22 on the Milltronics Centurion 6 SBC

    I just push over RS232 currently -- I bought these two things from amazon and use my laptop and the program EdytorNC (free software)
    ...
  19. i stopped using it more problem than not

    i stopped using it more problem than not
  20. Most of what's showing is the type of stuff that...

    Most of what's showing is the type of stuff that shows on my screen when it's executing canned cycles. This is in cycle when it got stuck

    The two lines N12 and N13 are the only program gcode...
  21. Re: Tapping confuses my machine, won't do it, wont tool change after failing

    Hopefully I'll have some time to play around with this some more, must have been a change in the control between Cent 5 and Cent 6.
  22. Thanks for the follow-up, interesting finding

    Thanks for the follow-up, interesting finding
  23. Re: Tapping confuses my machine, won't do it, wont tool change after failing

    Feed rate in the program is 0.0312 (feed rate should be in pitch according to the manual) and this is confirmed working on Cent 7
  24. Thread: Fusion360 post

    by yugami
    Replies
    11
    Views
    3,211

    Re: Fusion360 post

    You would need to post a sample section of the code thats being output for any troubleshooting to occur. I have not threadmilled on the milltronics. Hopefully someone has an example of something...
  25. Thread: Fusion360 post

    by yugami
    Replies
    11
    Views
    3,211

    Re: Fusion360 post

    The post is fine, theres a couple guys that grabbed it from the HSM Post forum (autodesk) using it for production (including rigid tapping)

    My problems are with a 26 year old machine being old.
  26. Tapping confuses my machine, won't do it, wont tool change after failing

    Doing any sort of tap op royally screws the machine. G84 or G88 and the machine sticks at that line.


    Heres the control display for the G84 N12 and N13 are from the program. The rest are the...
  27. Re: Machine decided to home x in the opposite direction

    Maybe not all sorted, but its homing correctly again.

    Doing any sort of tap op royally screws the machine up though. G84 or G88 and the machine sticks at that line. Estop or halt and tool...
  28. Think I got it all sorted

    Think I got it all sorted
  29. Machine decided to home x in the opposite direction

    Left the machine not estopped overnight, not my normal practice. But I warmed it up in the morning and everythings been going well.

    Experimented with G88 and the machine hung above the part...
  30. Replies
    6
    Views
    2,209

    Re: VM16A Max Tool Weight

    I did my drawbar washers with a kit sportybob sent me. Assuming you can get the motor and cover off out of the way (its heavy) Its fairly easy. Just take pictures to make sure you get everything...
Results 1 to 30 of 130
Page 1 of 5 1 2 3 4