584,846 active members*
4,038 visitors online*
Register for free
Login

Search:

Type: Posts; User: juniormachinist

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    4,606

    Re: VFS5 Kollmorgen drive

    Thanks Mike
  2. Replies
    12
    Views
    4,606

    VFS5 Kollmorgen drive

    Im looking for Motion Link software to communicate with a VFS5 Kollmorgen drive does anyone have a link thanks
  3. Replies
    21
    Views
    2,680

    Where are you ROSSITERENG

    Where are you ROSSITERENG
  4. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    Hi Mike just got in to work and checked again the light on relay CR13 stays on and does not go out when we run the spindle or get the error message is this right or wrong
  5. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    Hi Mike you mentioned in a previous post check that CR13 is turning on an off. this stays on does not go off is this still ok
  6. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    Ok CR13 is on and stays on all the time here is the io screen pics 1 before start spindle 2 spindle running 3 stopped error message Ive have watched the servo display and it shows the spindle speed...
  7. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    It knows where it is it positions it self for a tool change
  8. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    Not yet the I got the servo display up reads zero in the rpm so is there some sort of speed sensor some where
  9. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    Ok almost there with this thing now im getting this message 314578 any help would be appreciated ive nearly had enough of this thing
  10. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    Thanks Mike dont sell yourself short your 2 cents worth is worth big $ to us turns out the home switch will show in the io screen on initial start but to see the ot switch the on button needs to be...
  11. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    we think this machine has more than one problem trying to solve one at a time it had over traveled in the y on inspection the switch was physically broken the wheel broken of impossible to use we...
  12. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    Ok so we got the new switch and we still have no limit switch signal on the y axis the switch is good also checked the wiring back to the plug on the input board and all is good do you guys have...
  13. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    we are waiting for the switch to arrive and fit to see if there are any other issues
  14. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    Thanks for your help will let you know what the problem is if he can find it
  15. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    309376[ATTACH=CONFIG]309374
  16. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    Ok so turn the power on at back of cabinet press the green on button soft ware loads up everything says ok check the lights on the drivers one green and one red on all 4 I get someone to release the...
  17. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    sorry stuck an extra i in there and cant get seem to change it
  18. Replies
    32
    Views
    3,720

    Re: cincinnati sabre 4th axis problem

    sorry mike all the low voltage lights go out I have the prints will check today we were able to turn of the a axis
  19. Replies
    32
    Views
    3,720

    Attached is a picture of the pendent Also the...

    Attached is a picture of the pendent
    Also the red light is on for the z axis on the pendant
    And says z axis not ready on the pendant
  20. Replies
    32
    Views
    3,720

    cincinnati sabre 4th axis problem

    Recently picked up a secondhand cincinnati sabre 1000 with a acramatic 2100e controller and 4th axis included
    When machine is powered up we get a " Alarm 39-6 axis drives are not enabled" message....
  21. Replies
    0
    Views
    492

    x6 for solidworks tabs

    Hi,
    I am currently using mastercam x6 for solidworks and I notice when I want to insert tabs the option to do manual tabs is ghosted meaning I am unable to select the manual tab option and can only...
  22. You might be able to change your safe height ...

    You might be able to change your safe height

    Sent from my GT-I9505 using Tapatalk
  23. problem with a 3d cut mastercam x6

    we are trying to machine a ramp on a part using mastercam x6 for solidworks. when it is machined it leaves a step at the bottom of the ramp and we can't get it to go deeper. If you look at the image...
  24. Replies
    1
    Views
    695

    tapping speed

    can anyone recommend a speed to run spiral taps at. we mainly use 6x1mm, 8x1.25mm and 10x1.5mm. we are using compression/tension type holder
    thanks
  25. Replies
    6
    Views
    5,067

    Does changing the format mean that it chamges ...

    Does changing the format mean that it chamges

    - - - Updated - - -

    Does changing the format mean that it changes weather its imperial or metric
  26. Replies
    6
    Views
    5,067

    our pitch is right. all the numbers in mastercam...

    our pitch is right. all the numbers in mastercam match whats in the nc code. it outputs g95
    i have attached the same file we were using which is a 8x1.25mm as well as a 6x1mm file
  27. Replies
    6
    Views
    5,067

    tapping problems

    we have a 96 fadal VMC4020 with a cnc 88HS controller and are using mastercam x6 for solidworks
    we have recently began using tapping and have had limited success. we discovered that the feed rate in...
  28. Replies
    4
    Views
    605

    it didnt really help much due to the fact that im...

    it didnt really help much due to the fact that im using mastercam x6 for solidworks its a bit harder to find and i would like a free tutorial or as a cheap as possible
  29. Replies
    4
    Views
    605

    I've already done that but I can't the tool paths...

    I've already done that but I can't the tool paths to work
  30. Replies
    4
    Views
    605

    x6 for solidworks 4 axis

    how do you do 4 axis machining on mastercam x6 for solidworks?
Results 1 to 30 of 95
Page 1 of 4 1 2 3 4