Search:

Thanks for answering
I will try .

Hi,
I'm working on a FANUC FS 21MB.
My PCMCIA port is dead.
I backuped the ladder by the RS232 .
Is it possible to edit the ladder by Fapt ladder software from this file ?
Thanks;

HI,
I'm looking for tha manual B-62175 witch is maintenance manual for fanuc system 20
If somebody have it ..
Thanks

What kind of Leadwell ?

Hi,
I loose all parameters .( ram parity alarm )
I don't use the fapt .
If somebody has a backup , any help will be appreciated.

Hi
There is no ladder with The Micon8 , only a flow chart witch is on so easy to use .
For your turret,if you have change phase A/B detectors, you have first to check when you turn the turret that...

Your servo drive (A06B-6058-H###)is dead , short circuit transistor module or ccurrent loop on control pcb

Exactly same one, only software for motor (eproms) and parameters .

No, Orly displaying and editing is locked, but it still allais working

Thanks for reply, I know that , i'm sure there is a Data for that, but witch one ?

We are located in france, but we ship all over the world
Give me the parts number you are looking for

Do you have an external position codeur or an optic or inductosyn scale ?

Hi,
on one ZL203 equiped with mapps and Fanuc
I loose the absolute zero position on the parts catcher (controlled by pmm)
Does anyone know how to move the part catcher in manual mode to start the...

Your second position for tool change should be IN G30
parameter is #737

Hi,
I need all the parameters (NC and PC) for a Biglia B111 equiped with a Fanuc 0T control .
Your help will be very apprecied.
Thanks .

Hi
Is there somebody who have any knowledge on this product
i have exchange bubble memory and I need to restart the CAP.
I have already load all macro programs, set all CAP parameters and setting...

SO, FOR A FANUC 0 PMC-L
YOU NEED A FANUC ROM WRITER AND A FAPT LADDER WITH AN OLD VERSION 5 OR OLDER WITCH IS RUNNING FROM DOS ....

HI
OF COURSE
YOU ONLY HAVE TO LOAD YOUR PROGRAMM ON YOUR MEMORY CARD, SELECT 4 ONI/O SELECT, AND CALL IT BY M198P**** IN YOUR NC PROGRAMM

YOUR DRIVE PCB 0375 IS DEFFECTIVE , SURE !

THIS PCB IS A TAPE READER EMULATOR WITH
YOU HAVE TO CONNECT IT ON THE HE50 CONNECTOR OF THE TAPE READER
SELECT RMT IN THE SETTING SCREEN
YOU SEND BY RS232 YOUR PROGRAM AND THE COMMUNICATION...

hI
JUST TELL ME THE VALUE OF UOUR PARAMETER 125...

Try to change your net with faptladder on your computer, then, load back your new pmc .
This way always work .

Hi,
I have a backup of a vmc72 with fanuc 0M not serial , but only with 3 axis.
So you will have to search all the parameters for the fourth axis , not so hard for somebody who knows Fanuc, but...

Push at the same time the 2 arrows keys ( cursor and line) and your page will turn

For the automatic zero return, this is made by your pmc, not by fanuc, so look your ladder , may be you have a keep relay to cancel that
for your parameter, i think your machine use the flexible...

hi,
i send you the password by pm
did you receive ?

Hi,
tell me what number did you hage on setting page in I/O
after you can try that , make a dummy DB25 male connector with a jumper between 6, 8 and 20 , connect it on the nc and try to enter...

send me your email

hi,
i can send tou a complete back up for an Hitachi VS50 with fanuc 16miA
There is here lot of people who don't have any knowledge on hitachi machine.... take care :boxing:

you only have to turn by hand your magazine still the pot number one is in transfert position and then only to set parameter 1815 (apz) of the 4th axis in fanuc side To 0 , then to 1 .that's all