Search:

On my TC22 with the carousel empty push the S_T_M button enter 1 after the T then 6 after the M than enter and shift + the tool change will take place and
the machine will think it put tool 1 in...

I use a 7.5 hp American Rotary CNC grade converter to run a TC-22 and a series II cnc with no problems.
Can run both together plus my drill press

Sorry didnt mean to hijack

I should have them
I will look in the morning and if i do can photo copy them u and email them to you

Look at the main screen it has several boxes in which 6 is STM
Press 6 -look at top of screen-you can enter a tool number and enter-
then I think it says to press any key and it will execute the...

Can you show a wiring diagram on changing the connectors?
I looked for an adapter to do this same thing.
Atx power supplies are common but At supplies are harder to find now
Thank you for your time

I am looking for a z axis (Parvex)drive for my torq-cut 22
Seems I have a bad drive.
I was getting a z axis drive overcurrent fault so I swapped it out with a non Parvex drive and the z axis will...

You can run MAKEDISK from dos and it will make you a backup floppy
For your machine for your software version
There is also an other post where one person copied his harddrive when it went out by...

I just ordered a DOM for my TC-22 and the price was $250
I just ordered it but havent got it yet
EMI is great to deal with and have spent alot of time with me on the phone
lately and are in no...

By any chance does someone have a copy of the bmdcprm.sys file from a tc-22 running ver 4.89 software they would be willing to email to me?
Having trouble getting this file right.
Thank You

Would have to fire up my homebuilt router to check but cant you set units
per step in MACH 3 under config-motor tuning-steps per unit?
I would have to look at MACH 3 to see ,I dont recall offhand...

This seems to be something all of us with this machine goes through sometime or other.
Does your self a favor and back up your harddrive.
You can run a makedisk from dos to make a backup disc of...

Thanks ppascuzzi,I will do this.
When I first loaded the software It did create a bmdcprm.sys file but when I tried to run the machine I got the errors about the encoder res not matching and a...

I went out this morning and booted up the TC22.
It loads fine right up to enabling the drives.
The drives will enable and thats as far as I can go.
The maint page shows me that the
axis pos
...

OK Thanks,
I will try that .
Been down last couple days with head cold,how I got a head cold in 90 deg weather is beyond me.
Anyways back to the BP

I was given this disk to reload my harddrive when it crashed
I replaced the harddrive,formated .partioned it and made the partion active.
then loaded dos and this software.
Not sure of last...

When I I installed the harddrive I copied the bmdcprms.sys file from the old harddrive to the new after loading the software.
I will have to boot the machine andsee what version the software is.
My...

I was in the maint page on the tc-22 today just to check some parameters and am curious to why no parameter matches the manual
I was looking at parameter041-042-043

the manual shows them to be...

Thanks ppascuzzi
That gives me more to check out.
I am sure the axis is free falling as soon as the brake is released and not the drive powering the motor down
I am leaning toward a faulty drive...

I guess I didnt explain it correctly.
I have the correct voltage at the drives which I dont remember exacly off hand but think it was 144 volts I would have to check the manual again but was within...

een chasing this z axis problem with no luck.
Can someone advice me as to what proceedure to use to troubleshoot this?
When I enable my drives my z axis will drop all the way to thr table if not...

Thanks for the response.
That problem is solved,now I just have to figure out why it faults out during homing
Thanks again

Figured out the guards error I am getting.
It means the safetys are enabled in the control and wont home axis or do much with the door on the enclosure open.
I found this in the manual but cant...

I have my tc-22 finally back close to running with a fresh harddrive,dos install and software install and reman bmdc .
I have one problem .
When I enable my drives the z axis brake release and the...

Worked on the tc some more tonight and now can get the drives to enable but when I do the Z axis drops till I hit the E-stop.
I cant determine if it has power on it or if the weight alone is causing...

I put the new BMDC board in my tc-22 tonight and now I can get the machine
as far as getting to the point to reset the drives but the machine wont come out of e-stop
I have checked and have 24volts...

purchased a reman bmdc board today for my tc-22
Just want to know what you guys think should be checked before I install the board and put power to the machine.
I have read through previous post...

Rein staled the computer in the tc-22 today plus the bmdc.
There are no errors when I run the b3t.exe except the BMDC will not load.
Is this a fault in the BMDC or software loading from the...

I have been working with my torq-cut 22 bmdc
I have a 486 setup out of the machine to test with.
I have a new harddrive , powersupply and used MB that will get installed in the TC once all is...

Can anyone tell me what bmdc boards would be compatible with my
torg-cut 22?
My board is a bmdc 3s rev a
#31944009
fab #31944008

Will a bmdc 3s cv #32944367 out of an EZ trac work?
...