Thanks for the input.
In case anyone is interested the problem was the digital to analog chip on the DSP board.
Type: Posts; User: bertcnc
Thanks for the input.
In case anyone is interested the problem was the digital to analog chip on the DSP board.
I know it’s an old post.
Wondering if you got that mill. I desperately need a copy of the system software.I had Version 3.12A on my 3200MK but lost due to HDD failure. I have all manuals if you need...
Hi, everyone.
The hard drive died on my 2 axis mill with a 3200MK control. The original software version 3.12A is not recoverable.
I installed another HDD, with software ver.3.62 from a 3300...
Do you still have the Takisawa MAC-v2 with the 6MB?
I desperately need parameters especially the diagnostic parameters.
Happy to pay for any help
Bertie
Thanks for your reply.
Hopefully someone who has one of these mills will help.
Lost all parameters due to faulty BMU. A87L 0001 0017 08G.
Can anyone help please
FS 11M does not have 908 but 9108.5 =1
Thanks for the reply
Hi all,
I installed the parameters after a memory failure.Now a program stops at a G68 and reports an error.
Is it a parmater problem?
Can someone please help.
Thanks in advance
Bert
Hi All,
Has anyone got one of these or know where I can get any information350276350280
Thanks
Hi Everyone,
I want to run the spindle on a Cincinatti sabre with cmd signal from a battery box on C2-11 and C2-1.
All supply voltages and bus voltages are present. The system and cpu led's are...
do you still have them?
Interested if it's still available.. [email protected]
I have a TL5 Mori with a very noisy Spindle.I replaced headstock bearings. It is still noisy due to the gears being worn,
I can buy a scrap Sl 5 which I'm told had a good spindle.
Can anyone tell...
Thank you very much Superman.Looking forward to installing these and see if it runs.
Hi,
Can you still help with parameters for the Colchester cnc 2000L?
Thanks for your advise.Been in contact with Fanuc and they had the same problem on another machine.
They figured it was down to a keep relay but were unable to resolve the problem due to the lack of...
bit3 =1 ie 9108=hex 2C. G54-G59 works ok.
We use the presetter on a hitachi seiki and find it superb,no need to worry about test cut feedrate or spindle speed.
Your right though about the...
Hi, Are you still available on this forum.The machine still not running
Bert
hi, baltazarcopal,
Sorry I missed your reply. Available now
Bert
The TL40 F10TF is different. K5.7=1 is psmok =setter used.
This enables the PSM button when the arm is down. Any mode other than handle will issue a machine error and associated warning light....
Thank you underthetire I wil try Mori again for circuit diagrams and a ladder diagram but I'm not to hopeful.
274508274510
Hi, Thanks for replying. The ladder shows the presetter on and the probe signals G27.xx seem to be passed to the cnc ok.
Is there a write permit parameter or something missing which...
Can anyone help me with some parameters for a Mori seiki TL40.
I got the machine which had been lying for years with the memory batteries dead.
Mori UK could not get the originals but sent me ones...
Which model moriseiki?
I had the same problem.The fault was in the servo module.
Cheers
It has a 4 station turret Duplomatic I think.. Manual gear change spindle. Hope you can help
Thanks
Regarding the blown component on your spindax control pcb. A7S smd dual high speed diode BAV99 perhaps.
Cheers
Did you get my message?
Bert
I know it's an old post. If you still have problems i can probably help.
I know this is an old post but I have the same problem. I need a copy of S/W version 6.22A. Anilam don't have it..obselete now..Any chance you can help me?