Search:

Looking at your original program, on line N14 you have no decimal point, just Z0$, 99% sure you need it to be, Z0.$ or Z.0$ or Z0.0$ It's easy to miss those pesky little devils!

I only program in reg. G-code (EIA) so I'm not sure this will help much, but I've run this little program many times. All my programs are stored on a computer and downloaded every time I need to run...

On my machine I have to have T01,M06, E01 ect. T1, M6, E1, always gives me a error. I never tried T0001 like you have, which maybe OK, but I have heard other people claim you have to have 2 digits...

Don't Put "$" after program name (1234) and just use a "E" inplace of "END$" to end your program. You also can not have any program numbers in front of either the program name or the E at the end of...

Thanks jagardner4 for the info! I will give it a try today.

Thanks in advance! We have a Tree 1050 w/20m control. We program 90% off line (EIA) and have no problem loading programs to the control, but we always have to cut out all the comments in the program...

I found it! Hit the fault status button, then hit the status display soft key, then you have the option to turn on/off backslash delete. Thanks for the replies.

Thanks in advance! My Dynapath manual says my 20m control will respond to a backslash before N to skip a event or program line (if the machine has been set up with a switch). I can't find anything in...

Thanks in advance! I get a ton of knowledge from you guys and I've been machining for 39 years! I thought I knew it all at 21, realized I knew nothing at 31 and now hope I learn something everyday!...

2nd machine stops fine at 2500+ rpm, I did find 2 other parameters this morning, one for spindle acceleration "Value of 17" and a one for spindle deceleration with a value of 119. Both machines have...

I never seamed to have any problem before, but I hardly ever ran this machine at high enough spindle speeds to be in high gear. We recently had some storms and power outages while the machine was...

I am having a problem with my TC-22 w/dx-32 control. 2 speed gearbox on the spindle. When in low gear everything works perfect. When in high, say 2500 rpm, the spindle faults when the spindle shuts...

PROBLEM SOLVED. We Formatted the Hard drive, reloaded DOS 6.2 and then reloaded the DX-32 software and parameters, The machine did the same thing, Would not do the executive load on the BMDC. We...

I got some good info today. There is something in DOS like a hardware integration layer. When dos is set up for the first time it makes a few little adjustments. The way it sounds sometimes you can...

A bit of new news. When looking through my Maintenance Manual I found something that I missed earlier. It reads; The BMDC board is compatible with most IBM AT compatible systems. There are two...

OK, here is the latest. I swapped the BMDC cards, same problem, Machine 1 (original problem machine) still does not do the executive load. I put the BMDC from machine 1 in machine 2 (Working machine)...

Here is where I am at. I tried 3 different Motherboards that I was able to scrounge up. 1 didn't work at all, I believe it was just bad. The other 2 give me the same problem, Machine boots, DOS...

I think I am reading the hard drive ok, dos loads OK and the dx-32 loads until it tries to load the BMDC. I never received the original software floppys with this machine so I can't try to boot from...

I went through and enabled each region in the memory shadow one at time and I got the same result each time. Dual port memory test, Failed AT side address test, 030 side of dual port ram is OK,...

I got in the bios and System shadow is enabled, but does not allow me to disable, Video shadow and all memory regions are disabled. The only one that was enabled that I could change was the video...

Yes, as it is set now memory chach is enabled and memory shadow is enabled. I will disable shadowing and let you know what I get.

I will look for a different motherboard. The one I am trying to use is a Zeos International, #100-0052-00, They are long out of business with no support site. I did find some info at About.com...

I have not set any memory addresses in the bios. I looked all through the different bios pages and do not see where I could set any addresses for memory? IRQ's yes.

I am not ruling out a bad BMDC board, as problems tend to come in 2's and 3's, but this machine was running fine until the KB interface error popped up and there is visible damage from battery...

The fuse on my original motherboard is OK. About 6 months ago the Battery went bad on the motherboard. I replaced it with a external battery, but made the very stupid mistake of leaving the original...

Yes ,I am using the same Hard drive. I will check out the fuse you talk about on the original motherboard. Thanks for the help. I will let you know what I find out.

I am new to CNC zone as a member but have used the website for a long time to get good info! So my thanks goes out ahead of my question! My torq-cut 22 motherboard went bad (Keyboard interface) so I...