There are multiple code examples in the string below.
I’d advise using those.
Type: Posts; User: tea hole
There are multiple code examples in the string below.
I’d advise using those.
You do need the decimals on the D/U/H characters of code.
You also need a G50 command.
The alarm itself is because you don't have a G50.
Make it read:
N1
G50 S500
G40 G95
#
#
It is possible that this is a fixturing issue.
VZSHC would help a Y axis err if the holes were parallel to the Z.
I still believe it is a backlash during setup issue.
I have had this issue when...
took the words out of my mouth.
what you're effectively referring to is backlash in C axis positioning.
As a test, always rotate the C axis the same direction with the pulse handle to get the...
At first glance, what you're asking for is not 100% possible. There are local variables in your program being referenced which would be set in the parent program and carried into this program. For...
If by "free" you mean "spare" then I don't know if that shows up on the data management card anywhere.
You can try to look for the I/O's for them and see if they're labeled as L or not.
If they are...
I can't in good conscience recommend doing something that won't work 100% of the time. You can always drop N lines not being referenced. You can always drop preceding zeroes. You cannot always omit...
First, this is the Okuma forum, so the depth and breadth of replies may be lacking.
Next, there is a system variable to read the current position of any axis at the moment the line of code is read,...
It's upset because it's a bit lost.
It doesn't like having the G42 as it's first "move".
Make this:
NAT01 G81
G42
N0000 G00 X61 Z61
N0001 G01 X61 Z60 F0.1
N0002 G03 X63 Z59 K-1
N0003 G01 X63...
In short, you can float tap with a floating holder only. You can rigid tap with a floating holder OR a rigid holder.
You may have a small issue possible if you exit and re-enter a hole over and...
Glad you found your problem.
I'm not arguing with you.
All i'm saying is that for 99% of the world, this:
PSELECT A.MIN,,,Q6
END
is easier to use to get all the functions like the parts counter
425834
and cycle stop...
Not sure if you gave up on this yet, but...
In tool life management, i never use the screen you're describing. I use the main TLM screen you come to.
Item down to TLM (NO OF WORK)
Set the...
Schedule programs can have 5 types of codes in them.
PSELECT
GOTO
IF
VSET
END
It's in the manual. Page one of "schedule programs".
I know for a fact that there's a parameter to prevent the...
I've seen before where this nut backs off.
The set screw gets loose and the nut backs off allowing some severe backlash.
I'd suggest checking item 21 in the attached.
425798
I believe the answer is no.
Under gauging results is the only place i'd expect to find them if anywhere, but i haven't looked in that screen for a while and i don't have a mill handy to check.
That...
I believe it is a combo of a cost benefit equation as well as what you're trying to do this on.
First, at some point you can just buy a newer used machine for less money than what it would cost in...
Yes with an if statement you can check if a local variable exists.
Ex:
TIME=45
IF TIME N1
TIME=17
Please reference section 3-5: Torque Limit and Torque Skip Function
Pages 40-43 in the manual I keep at my desk:
P300S/P300L
Programming manual
9th Edition
LE33-019-R9
Pub# 5946-E-R8
dated...
Kitten, I do agree that you're making the G71 way too difficult.
Also, to insinuate that the rest of us do not cut tight tolerance threads in any production environment is pretty insulting to...
Yeah, gonna need more info than that to help really.
In a program you need a "T010101" for tool 1, "T020202" for 2 and so on.
Since the machine has multiple turrets, it needs to know which turret...
They community here is pretty helpful and supportive; as much as any internet forum anyway.
Probably above average.
Keep asking questions and someone will give you an answer...
https://www.okuma.com/osp-control-development
Feel free to click on the 1981 link.
After review, i will concede the LG was the control on the early 80's machines. The front panel had been...
insufficient data to help here.
The LB300 had different iterations of machine and depending on options, one parts manual does not fit all I don't believe.
what options does the machine have?
Though I agree it is an issue of age, a few things: the OSP5000 was built starting in 1981 and had become the 5020 by 1984 i believe.
Next, i don't think Okuma really "obsoletes" parts for the...
In short, nobody I know is using 3DVM.
newton11n:
this was shared here a while back as a resource: Answers and Information - Hartwig, Inc.
there are some pretty useful items on there. Some are "newer" and won't really assist you, but...
Genos M4/560 machines have a high enough Japanese content percentage to be labeled "made in Japan".
Think of the Genos as the "base model" with few available options and larger quantities of them...
I believe HiNC (and its variants) HiCut Pro and SuperNurbs all use G130/131 and it depends on which one your machine has as to which turns on.
you mention you tried the whole long line of code. Is...