Hello again-
I had a quote from someone in NY state, but the CNCzone messages we had are now gone from my cnczone account.
My client is ready to buy some, if you could please PM or email me...
Type: Posts; User: X35 Design
Hello again-
I had a quote from someone in NY state, but the CNCzone messages we had are now gone from my cnczone account.
My client is ready to buy some, if you could please PM or email me...
Hi Roger - thanks for the input.
Looking again at the drawings, perhaps we don't need such a tight callout on the OD, just a limit dimension on the OD that it's no smaller than x.xxx and allow a...
Sorry... email address for contact is
[email protected]
Thanks
Sorry.. emali address is
[email protected]
Thanks
Good afternoon-
I'm seeking a quote to have these two parts made, in qty of 10 each and 20 each. They are made of wear resistant nylon, similar to McMaster 8733K818.
PDF attached below. I can...
Hello -
I'm looking to get some sheet metal parts made in the Austin TX area so they can be picked up vs. shipping
Parts are 12 gauge mild or galvanized steel w/ grey texture powder coat...
We run two Mach3 based machines in our shop for cutting materials.
I'd like to be able to track the following information:
1. The programs that have been loaded and run
2. The uptime (or idle...
Hi Zone
I have a MAXNC 10 OL, that I am thinking of selling and I'm not sure where to start on pricing.
It is the smaller 8" X travel Open loop model. The original control box went poof one...
I'm not patient lol...
Wound up ordering a new one. Used Grizzly's 10% off coupon from their emails, so just $1235 shipped with liftgate service. Not too shabby...
Like the title says, any G0704 for sale? Prefer non converted as I have the control box, etc. already.
Within 6 hours' drive of the Dallas/Fort Worth area please.
Otherwise it's a new one for...
PDF drawing of above.
I am looking for two pieces of 1" square tubing, bent into a 90 degree corner with an approximately 12" bend radius.
We are flexible as to the wall thickness, depending on what is possible to...
Hi CNCzone
I'm looking for something like an ANSI P type drill bushing in stainless steel in two different sizes. Same or very similar ground ID/OD tolerances and ground chamfer/lead and inlet...
Still Looking......
Looking to buy a used mini lathe (7x12 size or similar benchtop lathe) somewhere in the Dallas TX / Oklahoma City region.
There must be someone out there who wants to upgrade?
Figured I'd...
Found some interesting things when I checked the backlash.
Z was .0006 - good
X was .0006 - also good
Y was .0014 - not so good.
So, I consulted the Tormach manual.
I completely...
Do you mean with a video or something?
I can probably do that over this weekend.
Bump...January is running out, along with my lease where the machine sits, so I'm getting a little more eager to make a deal to move this thing, so I don't have to arrange to move and store it...
I made a stand of 10 or 12 gauge steel sheetmetal angles, bolted together. Then I made a tray to put under the machine. It's very sturdy.
The whole stand is made of only two or three different...
Change in plans and pricing:
I am going to keep most of the accessories, so what I'm offering now are these items:
Tormach 1100 Series 3,
Purchased new in Feb 2014, mfg date 10/13
Custom...
Now finished with production, coroplast enclosure removed, and cleaned up nicely.
Tormach 1100 Series 3,
Purchased new in Feb 2014, mfg date 10/13
Custom Stand with drain tray
HP PC + Monitor...
And just a couple more..serious inquiries I can email you further pictures, specific views, etc...
This one shows that the buttons for the PDB have the typical cracked plastic on them.
Also, you...
And a few more....
Finally, some pictures:
297096
Here is a picture of the design of the stand that I made:
It is pretty simple. I have added a coroplast enclosure around it to keep the chips in. Nothing too fancy, you can have it with the...
For Sale, available as soon as I finish my currently running job:
Tormach 1100 Series 3, Feb 2014 purchased new
Custom Stand with drain tray
PC w/ Mach3
Manual Oiler
Tormach Load meter
Power...
Vendor will be chosen Monday, Sept 14.
Thanks to all who sent in quotes.
I'll choose the vendor on Monday the 14th. Thanks to all who sent quotes in.
Hello-
I'd like a quote for the the following washers:
20 of each size
40 of each size
80 of each size
Material is Rigid HDPE 3/16"
Large washer is 2.88 OD x 1.36 ID
Small washer is 2.00...