584,849 active members*
4,227 visitors online*
Register for free
Login

Search:

Type: Posts; User: hernault

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    1,246

    Re: 4TH axis powered by delta servodrive.

    Hello.
    It is done. My motor is repaired but i have always the same problem. The limit of the speed. Something new. below 1190 tr/min the speed is the same clockwise and counter clockwise. If i...
  2. Replies
    5
    Views
    1,246

    Re: 4TH axis powered by delta servodrive.

    Hello everyone.
    Thank you for your answers. At this time my project is off. I was grinding the shaft of the motor so that it fit with my 4th axis when the fuses have blown. Inspected the motor,...
  3. Replies
    5
    Views
    1,246

    4TH axis powered by delta servodrive.

    Hello.
    I would create a 4th axis on my vm25 then i buy delta servodrive and motor. I buy delta material because it was much less expensive than yaskawa. My motor is able to run till 3000r/min but if...
  4. Replies
    3
    Views
    1,322

    Re: centurion6 doesn't shift to the 2nd speed.

    Hi Allen mullis.
    You are right. I misspoke. Before understanding how the command of the spindle works i started the spindle with the M3 and increased the speed slowly by s200, s400, s600......But...
  5. Replies
    3
    Views
    1,322

    Re: centurion6 doesn't shift to the 2nd speed.

    Hi.
    I solved the trouble.
    Centurion shift only with a M3 or M4 command.
    Best regards.
  6. Replies
    3
    Views
    1,322

    centurion6 doesn't shift to the 2nd speed.

    Hi everybody.
    I have a centurion6 control with a 2 speedmotor yaskawa.
    My problem is centurion6 doesn't shift to the 2nd speed when i command a speed over 1500rpm.
    I was searching in my parameters...
  7. Replies
    0
    Views
    810

    Need help with a wild centurion6

    Hello.
    It's been a long time now since I started fighting with my centurion6.
    The problem is a have neither spindle drive nor ATC. So I try to simulate them by connecting the inputs to 0V or 24V....
  8. Replies
    6
    Views
    1,809

    Re: SRAM Freespace=-1

    Hello Sportybob.
    Thank you for your interest. I a fought something strange. There is a difference between the list of my centurion parameters and the parameters of the manual.
    My version of...
  9. Replies
    6
    Views
    1,809

    Re: SRAM Freespace=-1

    Hi Sportybob.
    Here are the pictures you asked me for.
    At this time i still can't use my CNC. It takes a long time for me to repair it because i do it in my free time.
    This problem of the control...
  10. Replies
    6
    Views
    1,809

    Re: SRAM Freespace=-1

    Hello Sportybob.
    I finally succeeded in formatting my B:drive using the method you gave to mortyNtenon and the help of a french nice guy.
    Thank you to both of you.
    But i'm a little disappointed...
  11. Replies
    6
    Views
    1,809

    SRAM Freespace=-1

    Hi.
    A have a new problem with my centurion6.
    A have the message SRAM Freespace=-1
    I have changed the 2 batteries : the BIOS battery and the ISA card battery but it still doesn't work.
    I have...
  12. Re: How I can match centurion6 with my milling machine.

    Hello.
    I found a solution with centurion6 parameters. It needs to change the parameter pulses per unit.
    To change this parameter : parameter/config/level(proto3)/axis/pulses per unit.
    Thank you....
  13. Re: How I can match centurion6 with my milling machine.

    Hello.
    I have fought a solution by using the CN0A parameter that is PG dividing Ratio but it's not satisfactory.
    When CN0A=1250, one turn of the shaft of the motor moves the load to 6.35mm. I want...
  14. Re: How I can match centurion6 with my milling machine.

    Bonjour Lauchu.
    Merci pour ton aide. J'écris en anglais pour faciliter la vie de nos lecteurs.
    I can see parameters that CN2B is 0 for speed control. I am surprised, i thought the priority of a...
  15. How I can match centurion6 with my milling machine.

    Hello.
    I think you remember me. I'm on hollidays and I would like to continue my project but i have found a new problem.
    The problem is how I can match the centurion6 control with my milling...
  16. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi. Everybody was right. I 'm getting tired thinking about this machine. I bought it because it was quite cheap and more little than a VM25 for my little garage. I will give up the idea of running it...
  17. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi. For sportybob. I have already pulled the pin from X out 11 and it's always 0,6V. Even in MDI mode it's impossible to clearX11. On the display screen, if a write in MDI SETX11, Xout11(spindle...
  18. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi everybody. For Sportybob. I have a centurion6 with 24V contactors. After my machine has just been on, before resetting, Xout11 is already 0V and K10 is immediately enabled. For Allen mullis. I've...
  19. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi Allen mullis. I have already put the parameters zero speed and up to speed both on no. When they are on, it blows the whole circuit. Today i gave centurion a spindle encoder and it works...
  20. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi everybody. I agree with you. First, when I put an M3 centurion turns on Estop after 5 seconds with a message. I don't remember exactly the message but it told me centurion was waiting for...
  21. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi sportybob. I have changed all the ULN2802 by new ones but centurion works in the same manner. It doesn't change anything, i'm disappointed. Always Xout11=0V before resetting. Xout4=0,7V after an...
  22. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi sportybob. Your message is incredible. Thanks a lot for your help. The commands you told me about work. setx4 works like an M3 and clrx4 like an M5. I can see in the display x4 turn to 1 or 0. But...
  23. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi. Perhaps my first problem before M3 and M5 is the Xout11 that coils the relay K10. When i start centurion before reseting, Xout11 is at 0V and K10 is already on. After reseting, Xout11 is at 0,3V...
  24. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi allen mullis. I've just tried what you told me to do but centurion answers :518 Illegal program statement ...
  25. Replies
    25
    Views
    3,517

    Re: Problem of spindle.

    Hi allen mullis. I would like to use an altivar because i already have one. But my problem is a problem of control and i think a yaskawa f7 drive would'nt change it. When i went to displ/diag i saw :...
  26. Replies
    25
    Views
    3,517

    Problem of spindle.

    Hi everybody. I've got a problem and i need your help if you please. My project is going on slowly. As you know for those who already read my messages, i don't have the spindle servo motor for my...
  27. Replies
    2
    Views
    711

    Re: My centurion save........nothing.

    Hi newman55598. I have done what you told me to. I chose to open all files and now i can see my program. Thank you. Happy new year.
  28. Replies
    2
    Views
    711

    My centurion save........nothing.

    Hi everybody. Now, with your help my centurion is working. Thanks to ZZZZ, allen mullis and sportybob. I try to use it. When i bought centurion there were already programs inside. I would like to...
  29. Re: Error 450 on centurion 6. Need code for builder.

    Hi sportybob. Yes i have a wiring diagram, ZZZZZ give it to me. I have solve the problem. Now i control my motors and i need to purchase antiback lash screews. It's for a little french machine (see...
  30. Re: Error 450 on centurion 6. Need code for builder.

    Hi allen mullis. THank you for the code and for the ideas. I went to F7(parameters)/F1(level)/F3(power) then i disengaged the spindle by putting it on 0, then I put ATC 12/20 to --- After that the...
Results 1 to 30 of 40
Page 1 of 2 1 2